Models
>
JGP5030SL2SS
JGP5030SL2SS General Electric Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGP5030SL2SS
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
$38.56
This medium gas surface burner provides steady, even heat for everyday cooking tasks such as sautéing, simmering, and boiling. Made from durable, high-heat-resistant materials, it restores proper flam...
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
$15.26
This economic nut is a manufacturer-approved replacement part for your oven range. The nut can become worn down or stripped over time and need replacing. Make sure to disconnect power to the unit and ...
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
In Stock
Order now and your part arrives by Aug 13
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- terry from NAPLES, FL
- Parts Used:
- WB13X29294
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Electrode would produce spark to lite burner
The following are steps in replacing a burner electrode for GE Profile Cook Top Model PGP7030DL1BB
1. Shut off gas and unplug electrical plug
2. Remove all stove grates and turn on knobs
3. Remove all burner covers
4. Remove all screws [three for each burner]
5. Remove two screws near front by removing rubber gra ... Read more te grommets
6. Carefully Lift off stove cover and set aside
7. Remove shield near back of stove top. This exposes all burner wires
8. Remove electrode to burner which does not lite by sliding out clip at bottom of electrode—note color code of wire and replace with same. Change one electrode at a time to insure wire color code is correct.
9. Reassemble in reverse order of steps 1-8
HAVE A NICE DAY
1. Shut off gas and unplug electrical plug
2. Remove all stove grates and turn on knobs
3. Remove all burner covers
4. Remove all screws [three for each burner]
5. Remove two screws near front by removing rubber gra ... Read more te grommets
6. Carefully Lift off stove cover and set aside
7. Remove shield near back of stove top. This exposes all burner wires
8. Remove electrode to burner which does not lite by sliding out clip at bottom of electrode—note color code of wire and replace with same. Change one electrode at a time to insure wire color code is correct.
9. Reassemble in reverse order of steps 1-8
HAVE A NICE DAY
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Drury from Newport, NH
- Parts Used:
- WB16X24722
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Hi output burner never worked correctly. Burned unevenly and created soot.
So for years have been struggling with this burner. Technicians could not figure out the problem. Then one day, I noticed that the top cover did not sit properly on the burner. Lifted up the burner with the cover on it and noticed that the burner itself was warped and deformed. The top cover never sat evenly on the burner. Ordered a
... Read more
new burner and put it in and presto. The burner work properly for the first time since we bought the stove. So, check the burners and see if the top cover sits evenly on the burner.
Read less
Was this instruction helpful to you?
Thank you for voting!