Models > JBP60BY2WH

JBP60BY2WH General Electric Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for JBP60BY2WH

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
This oven handle end cap connects to your oven door handle, and acts as the joint that connects it to the oven door. This part is made of black plastic and can be used as the left or right-side end ca...
In Stock
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
In Stock
This bake element has push-on wire terminals and the feet to keep it elevated from the bottom of the oven.
In Stock
This haliant burner element is a gneuine OEM replacement part for your stove. This element is 8 inches in diameter. The element lies underneath the stovetop, and will need to be replaced if it stops h...
In Stock
$72.53
Sold individually.
In Stock
In Stock
$82.67
In Stock
These are replacement screws designed to fit your range. They are made of metal and are approximately ¼ inch long. They come in a package of 12. These are OEM parts sourced directly from the manufacturer.
Special Order
This broil element is found on the roof of the oven.
In Stock
In Stock
This part supports the broil element in the oven.
In Stock
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for JBP60BY2WH

Viewing 4 of 4
Element will not heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Little to no heat when baking
Fixed by these parts
Fixing Fixing
How to fix it
Little to no heat when broiling
Fixed by these parts
Fixing
How to fix it
Oven not heating evenly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Kevin from Leominster, MA
Parts Used:
WB30T10045
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Large burner would not get hot
Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!
70 of 92 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alton from Marshall, TX
Parts Used:
WB44X10009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Bottom heat element
Turn the breaker off to the oven.Removed both wire racks,using a 1/4 nut driver unscrewed the old element.The flashlight was so I could see inside the oven.Having removed the two screws ,the old element came right out.With my needle nose pliers removed the wires one at a time,replacing them on the new element as they came off.Replaced the two screws holding the element ,replace my wire rack, turned the breaker back on.As for the price for the part ,it was less than a service call from a repairman,which would not have included the part.
50 of 53 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Frank from St Augustine, FL
Parts Used:
WB30T10047
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Coil Burned Out
Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak
60 of 91 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!