MBC12GAZSS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Elizabeth from MECHANICSBURG, PA
- Parts Used:
- WB29K10024, WB29K10023, WB29K10022, WB28K10222
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
This was not really a repair. Just replacement. The burner caps get discolored rather quickly and nothing removed the stains. I'm thrilled to have replacements on hand.
Removed the old caps, replaced them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Waukegan, IL
- Parts Used:
- WB2K101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner grate bumpers/feet missing
Hi temp (900 deg) engine gasket adhesive on numbs and press in. DONE !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mchael J. from Chesterfield, VA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven post mini explosion sounding
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from South Haven, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Santa Rosa, CA
- Parts Used:
- WB29K10024, WB29K10023, WB29K10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our burner caps had started chipping.
Was able to see the exact part with easy to read schematic so I knew I was ordering the right part. Then just switched out the old for the new. Looks like a new cooktop except for the scratches in the stainless, but we are working on that! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brigitte from vacaville, CA
- Parts Used:
- WB31K10217
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The griddle needed to be replaced
Lifted the old one off and placed the new one on. Fits perfectly and looks great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitzi from Briarcliff Manor, NY
- Parts Used:
- WB28K10222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original burner cap was chipping; must have been dropped somewhere along the line.
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mel from LOGAN, UT
- Parts Used:
- WB20K10027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
temperture
replace sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert K from York, PA
- Parts Used:
- WB16K10070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed To Replace Burner
Took longer to open the box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ARDMORE, PA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PLAINFIELD, NJ
- Parts Used:
- WB2K101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Misleading ordering information: a HUSTLE
I specifically asked if $16 plus would be the sole expense for this item. I was told that it would be plus there would be no cost for return of the rubber feet. Several hours later I was emailed an invoice that the cost would be $26 plus for four rubber grill screw-like items, a vastly over-priced item. I called and learned through the email system that the item had not been shipped. I requested cancellation at 5AM Saturday. Friday night order led to Saturday morning cancellation -- and Monday morning delivery despite my specific request to cancel. I am not satisfied. It seems like I have been hustled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BRADENTON, FL
- Parts Used:
- WB21X20262
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burner Valve stopped working
Turned off gas, then lifted up the burner cover and removed the old valve using a screw driver to loosen the clamp. I also had to remove the face plate using a socket set (4 screws). I didn't align the valve using the existing valves as a guide and also didn't get the clamp tight enough. So I re-aligned the valve to match the other valves and also tighten the clamp enough as best I could to prevent gas from leaking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Plainview, NY
- Parts Used:
- WB29K10024, WB29K10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner caps began to chip
I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Astrid from MORAGA, CA
- Parts Used:
- WB16K10055, WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
I JUST EXCHANGED THE BURNER AND BURNER CAP.
Was this instruction helpful to you?
Thank you for voting!