JB735EP1ES General Electric Range - Instructions

Replacement was extremely easy. The new part fit perfectly and installed very easily without tools. Also, I received the part within a few days

Unplug range, pull out to access back panel. Remove enough screws to access the burner switch. Remove knob, 2 screws hold the switch, remove them. You can now pull the switch out the back. It had 2 electrical plugs remove them. Install on new switch and put back together. The switch I got was exact replacement, thanks partselect

Ordered window pack from PartSelect then removed oven door from front of stove, then removed back of door and silver backing and glass pack. Dropped new glass into place. Replaced all backing,put door back onto stove. Tip. When removing screw keep them separated from each other as not to get mixed up when putting everything together. Good Luck, PartSelect has all the parts you need, this my second getting a part from them.

Unplug range and pull it out to access the back. Pull knob off bad control at front making sure to check the orientation of the rod the knob goes on—it matters—and remove two brass screws. Then remove the four hex screws holding the top metal panel on at the back of the range (two have washers) and lift the panel off to expose the controls. (I then took a photo of the switch in situ to remember its orientation and how the wires were connected.) Use pliers to remove wires, then connect up and install the new switch, and put the brass screws back in at front to hold it in place. I used the pliers to turn the rod to the correct orientation before putting the knob back on. Reinstall the back panel with four hex screws. Plug the range in and test.

FYI the directions for accessing the infinite switch that came with the range also had me remove two screws under each side of the front of the control panel, but as far as I could tell that wasn’t necessary.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Unplug the range, remove the screws on the top third of the rear cover, remove two screws from the controller on the front side of the range, hold the rear cover open and pull the controller out of the back of the range, then unplug the two connectors from old controller. Plug the connectors into new controller, secure controller with screws on the front of the range, replace the screws on the rear cover, plug the range in.

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

I viewed the video available through part-select. The most important thing I learned to do was to change one wire at a time instead of removing the old switch completely and then installing the new one. With 5 wires involved, it was really simple to install and not have to remember which wire went where. I was surprised how easy it was and it works wonderfully!

Pull oven away from the wall. Unplug from 220VAC outlet. Remove six (6) black screws from the upper back panel. Remove two (2) screws and washers from top of upper back panel. Rotate panel down and pull away from the back.

Remove burner control knob. Remove two (2) screws from burner control. Pull burner control backward through the open back. Disconnect upper and lower cable bundles.

Connect lower and upper cable bundles. Push control knob post through the front on the range. Install two (2) screws to hold the burner control. Install burner control knob and turn to the off position.

Reinstall upper back panel. Secure with two (2) silver screws with washers. Install six (6) black screws.

Plug in range 220VAC cable. Slide oven back into place.

Tested burner on high small burner, low small burner, high large burner, low large burner. All tested fine, burner cycled on/off cycles as expected.

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

I pulled the stove out, unplugged it, screwed off the top back panel, held the control switches side by side and switched wires out one at a time. Put everything back together and pushed the stove back. Everything works like a charm. I’m a 60 year old female and that job took me 20 minutes start to finish-easy peasey.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Remove cover on back remove two screws for switch and take picture of wire placement install new switch put all back together
U. Plug stove first . Was really easy to do now have room do a other burner

Replaced infinity switch: unplugged stove;. Removed upper back panel (4 small screws using socket wrench. Appropriate size box wrench would be fine, too); pulled off burner control dial. Removed 2 small screws with phillips screwdriver. From back of stove noted position of infinity switch . Replaced wires, 1 at a time, onto new switch. Pushed new switch
into same position as old switch. Secured with the previously removed screws. Replaced the control dial. Replaced upper back panel of stove.

1.) I removed the old oven door gasket by taking out the ends of the gasket out of the bottom of the oven door first.
2.) Pry up on each one of the retainer clips, they easily pop out of their slots.
3.) Work your way around the oven door gasket.
4.) If any remain stuck you can just wiggle the clip around and it should pop out of each hole. If need be you could use pliers, but I did not need to.
5.) Take your new gasket, it should already have new clips, so you can throw away the old ones.
6.) Work your way around the oven door making sure the clips are nicely seated.
7.) Finish off by inserting the ends back into the 2 holes on each side of the bottom of the oven door, I just used a small spoon to make sure the tops were nicely placed in.
8.) If your gasket needs to compress, you can close the oven door and lock it that should hold it in place and compress it.
9.) All done!