CTD90FP3N1D1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andrea from SILVERTON, OR
- Parts Used:
- WB26X35089, WB27X28659
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
F97 on right side of double wall oven
My less than 2 year double wall oven was showing a F97 on the right hand side of display screen on my oven, indicating to me it was a lower cooling fan issue. Purchased the parts after a lot of research (and a GE technician telling me over the phone it would be a 600 or more costly repair). I decided to bite the bullet and just do it myself to save money! I’m glad I did! I built a table for it to rest on after it got it out of the wall as it’s a heavy oven. I asked my dad to help me get it out and onto the stand. After that, it was a matter of getting to the lower fan through the back abs having to remove some panels. All went well and best part is this fixed it! I figure even if it goes out again in 2 years it’s still cheaper than paying a technician to do it! I’m a woman with zero background in repair but lots of determination and desire to save money! Just do it yourself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from ROSEVILLE, CA
- Parts Used:
- WB26X35089, WB27X28659
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Double oven was providing a F97 error when we would attempt to pre-heat.
I ordered the fan and the sensor. I had to pull the whole oven out anyway, why not replace both. Bought a piano dolly at Harbor Freight so I could set the oven on something while it was out of the hole. Make sure and remove the oven doors and racks prior to pulling it out. I was not able by myself. A neighbor had to assist. The fan and sensor are located mid-way up the middle of the rear panel. I just take pictures with my phone as I disassemble so I have a roadmap for reassembly. Once I plugged the fan and sensor in I tested the oven while still out of the hole. I used the vegetable oil to provide a little lubrication to the runners while sliding the oven back in. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from PALM COAST, FL
- Parts Used:
- WB25T10102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
A burnt out bulb
After opening the Oven door, I removed the glass cover to view and locate the bulb, at the inside, top front of the Oven. Removed the burnt out bulb by pulling it in a forward motion towards the front of the Oven, slid the new bulb into place and the Oven is again functional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from HASLET, TX
- Parts Used:
- WB21X10165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven was burning when cooking at same temperature we always cooked it on
there was one screw holding it on the back wall of the oven. It was easy enough that my daughter installed it with my guidance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Bremerton, WA
- Parts Used:
- WB21X10165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would not hold an even temperature.
I used a Trox bit to remove one screw, replaced the oven sensor and reinstalled the screw. The whole project took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FAIRFIELD, OH
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven meat probe broken
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
- works great. tested it....snaps in, reads correctly, snaps out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTHBURY, CT
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salih Hindas / from SPRNGFLD GDNS, NY
- Parts Used:
- WB21X10165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Went well.
Changed the Temperature Sensor as you suggested, but the problem of 40 minutes to reach a temperature of 375 degrees F. remained the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MENIFEE, CA
- Parts Used:
- WB25T10102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt out lamp bulb
Remove oven light lens cover, remove the bulb and replace it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Munt Laurel, NJ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Probe broke
Ordered new probe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John R from Asheville, NC
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing meat thermistor
plug in thermistor when needed
Was this instruction helpful to you?
Thank you for voting!