J2B915SEH2SS General Electric Range - Instructions

First I slid the stove out and unpluged it, then removed two screws,slid out element, disconected two wires, slid new element in to place, pluged two wires in ,put into place and installed two screws, pluged stove back in, and turned on to try. Works perfect.

1)Turn off power to stove
2)remove 2 bolts holding heating element
3)pull element out of the back of the oven about 8" so that the wire connects is visable
4)pull wire clips off of heating element and remove element from the oven
5)put wire clips on the new heating element
6)push new heating element back into the holes in the back of the oven
7)screw botls back into the oven holding the heating element in place
8)Turn power back on

Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. There are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

Per the instructions included with part.

It took considerable time to remove the door and take it completely apart so the gasket could be inserted, and time again to reassemble properly. The gasket (though the no. was confirmed before ordering) was 3" too short so I had to cut some off the old gasket to make do (not entirely effectively).

replaced all four top burner spark electrodes. the same two still didnt work. I had also purchased spark module and that did fix the problem. Lifting the cook top was difficult. I was afraid of breaking the sealed burners. Note there are directions in envelope on the back side of the stove. /use pliers to remove connectors from module. >Getting the top open was the hardest and most time consuming.

Very simple repair. I bought the Range without the Burners and Burner Caps. So all I had to do was to purchase the Burners and the Burner Caps and drop them in. Wish everything in life would be that simple.

Removed screws using nut driver. Pulled element way forward until wires came through. Pondered how to detach burned out element from wires. Chickened out, call neighbor who grasped things firmly with two hands and pulled. Old element came loose. Popped in new element. Cursed the screws that wouldn't align with holes to support element; finally did it. Screwed element plate in place. Put oven door back on, plugged it in and turned it on hoping that we hadn't reversed the wires. Job accomplished.

openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over

My husband did it, we unplugged the stove first then he removed the damaged element replaced it with the new plugged it back in and we were in buisness. I like that this was an acutual part for my stove(not some universal thing) and it arrived very quickly.

Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.

I downloaded the installaion manual from the web for this model. First htings first, I located the circuit breaker for the oven and turned it off. Removed the lower trim piece from the bottom, next lifted the oven door off its hinges and set it to the side. I then wrapped a couple of small towels around the hinges for the door as per the manual (the hinges can pinch a finger). I then removed the four screws which secured the oven into the cabinet. Next I slid the oven forward allowing me access to the rear. I removed the pieces from the rear to gain access to the sensors connector, and unpl;ugged the sensor. Went around to the front and unscrewed the 2 screws securing the sensor and removed it. I then installed the new sensor, replaced the rear covers, slid the oven back into the cabinet, secured the four screws, snapped on the lower trim, remounted the oven door, and turned the breaker on. Oven working fine now.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.