JM93R5 General Electric Range - Instructions

The hardest part was removing the old nuthead screws off the old bake burner. Once those were off installing the new bake element was simple. One screw in each wire terminal, two hex head screws to hold the unit in place. Works like a charm!

Very easy, remove two screws, pull burner unit out slightly, then remove the two screws attaching the wires, one to each side, remove old unit and replace with new unit and replace screws.

Works fine perfect replacement.

Removed the racks, unscrewed the back plate which holds the element, unscrewed the leads from the element, removed the old part.

Reversed the process to install the new element.

Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.

And that was it; quite easy.

First I opened the shipping box that the new part came in and figured out which tools I would need. Then I went down to the cellar and clicked off the breaker that supplied power to the oven. In this case, it was the only 50 amp breaker in the panel so It was easy to figure out.
Then I hung a drop light inside the oven so I could see clearly and used a quarter inch drive ratchet with a quarter inch sized socket to remove the two self tapping screws that hold the element plate to the back of the oven. Then I used the same sized socket to remove the small screws that hold the wires and terminal ends to the element contacts.
Then I removed the old unit, placed the new one inside and reversed my steps till the new elements leads and bracket were both securely in place and the element supports were resting on the bottom of the oven. I then turned the power back on and set the oven for 350 degrees and switched the 'bake' selector on. Within thirty seconds, I had a nice even heating new element that glowed brightly from one end to the other. Success! Piece of cake. In the future, I plan to get all my appliance parts at PartsSelect.com and do a lot more repairs myself instead of just replacing the entire appliance.

Greg G. - Peabody, Massachusetts

I shut off the power at the breaker. Then I checked that the power was off by turning on the stove. Light did not come on, power is off. [ By the way, I locked the breaker box, in case somebody helpful came along to turn the power back on !] Then I undid the screws holding the old element . Pulled it out, and undid the screws holding the wire leads to the element. Screwed wire leads to new element. Pushed back in, and screwed brace screws back in. Went out to breaker box and turned power back on. Turned on oven. Worked. Second time I've done this. I kind of forgot how, since the last time was about 6 years ago, but anyone could figure this out, unless they didn't want to. Took 20 minutes. A little hard working in a small space , but beats buying a new stove.

Old gasket had become brittle. Was able to find the 22 yr old model and part on PartSelect (could not track it down on GE's site. Inner panel was removed with four screws. Old gasket came out. Installed new gasket making sure the bead fit into the groove provided in the door panel. Re-assembled. All is well. Thanks

total of 4 screws to remove and replace. Took out the first 2 and pulled element out a few inches. now remove the screws from the element itself but be sure you don't loose the wire out the back of the oven. The only challenge was to keep the wires from falling back through the rear of the oven. This could be easily avoided if you have a clamp of some type ie. clothes pin, hemostst, shop clamp ect.

Cut off power, but needed flashlight to see what I was doing. Couldn't get the flashlight to shine on right spot and had no one to hold it. Oven is 19 years old, so screws holding it into the oven wall and to the connection were very old and very difficult to loosen. Finally held prong with pliers and wrenched the screw loose after repeated tries and using a little WD40. Very proud of myself! I am a wife and mother of two teenage boys, but I end up doing all these projects. So proud that I posted a photo of the oven on facebook! Goes from 0 -350 in three minutes now. Yippee!

Replaced baking lower element by disconnecting the mounting plate and wire connectors at the base of the element and then reinstalling new element by reconnecting the wire connectors and mounting plate. Key to this project: Know how to identify the cause of the problem as the crack in the baking element was not immediately visible until it was removed. One could easily have assumed that some other part of the range controls were defective.

First, and most importantly, flipped the circuit breaker and turned off the power to the oven. Next, Unscrewed the old element and disconnected the wiring. Then, removed the old element and replaced it with the new one.
Reconnected the wiring to the new bake element and screwed it back onto the oven.

Voila! Turned the oven on and watched the new element heat to a bright red. We had an oven once again, and saved ourselves more than $100. Yay!

Ordered Bake Element - 240V from Partselect , when part received removed broken element with a screwdriver., replaced with new Bake Element with a screwdriver. Very easy to do.

Removed the racks, removed two screws holding the element to the back of the oven, removed two screws holding wires to the element, installed by the reverse. BUT in my case the new element still didn't heat. The part was perfect so when the old element melted and shorted, it must have damaged the controlling switch (220V requires dual pole switch--apparently one side is now bad). Since the oven is over 30 yrs old, I'm returning the element and will buy a new oven.

I turned off the breaker to the oven. Removed the old element and replaced. Turned on the oven breaker and turned the over to 350 and it was working great. I was very proud of myself as a 68 year old widow.

USE A MAGNETIZED SCREW DRIVER. BE CAREFUL THE OVEN ELECTRIC WIRES DO NOT FALL BACK INSIDE OF THE OVEN. HAVE LONG NOSE PLIERS HANDY. MAKE SURE YOU TILT THE ELEMENT SO THAT THE ELEMENT TERMINALS ALIGN PROPERLY WITH THE THE SCREWS AND ELECTRIC WIRES. THAT'S IMPORTANT ELSE YOU CANNOT GET THE SCREWS STARTED TO ATTACH THE ELEMENT.

Turned off the power to the oven. Removed the racks. Removed two screws holding the unit to the back of the oven. Removed two screws holding the wires to the terminals. Removed the old unit. Reversed the process. Piece of cake. The only "difficulty" was that the old wire-to-terminal screws required a nut driver (as did the unit-mounting screws) while the new wire-mounting screws required a #2 Phillips screw driver. Took me a couple of minutes to get one of those from the garage.