Models > J351*01

J351*01 General Electric Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Range Infinite Heat Switch Kit – Part Number: WB21X36771
$51.97
The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.
On Order
8 Inch Surface Burner – Part Number: WB30X348
$58.09
This surface element kit includes an 8 inch element, two wire, 2350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
In Stock
Order now and your part arrives by Mar 19
Tilt Lock Hinge Mounted Surface Burner Kit - 6" – Part Number: WB30X342
$51.97
This tilt lock hinge mounted surface element kit includes a 6 inch, three wire, 1350 watt surface element, and a terminal block with all three-wire units. These high rise elements do not come with an attached trim ring.
In Stock
Order now and your part arrives by Mar 19
Oven Sensor – Part Number: WB21X158
This sensor offers 16 ohms of resistance at room temperature, though the resistance increases as the temperature increases.
No Longer Available
Timer Kit – Part Number: WB19X10008
$273.79
This kit replaces some mechanical clocks. ***Please NOTE: The wiring of this part may be difficult and it is best to have it installed by appliance repair person.
Special Order
DISCONTINUED – Part Number: WB24K2
No Longer Available
CONTROL BD – Part Number: WB24X162
No Longer Available
DISCONTINUED – Part Number: WB24X190
No Longer Available
DISCONTINUED – Part Number: WB22X53
No Longer Available
DISCONTINUED – Part Number: WB24X131
No Longer Available
DISCONTINUED – Part Number: WB21X180
No Longer Available
DISCONTINUED – Part Number: WB24X108
No Longer Available

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for J351*01

Viewing 2 of 2
Element will not heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Little to no heat when baking
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ernest from Bellevue, NE
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
Large burner would operate on high setting only.
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.
22 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ryan from Henderson, NV
Parts Used:
WB21X158
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
oven temperature too low
After ordering the proper part with the help of the phone customer service tech, I moved the stove from the wall, unclipped the connector, removed the two screws holding the sensor in place, and removed it. Reversed the above to put it back, and the oven holds perfect temperature.
16 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clarence from Norwich, NY
Parts Used:
WB21X158
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
oven would not come up to temperature
Removed sensor from back wall of oven by removing 2 screws from flange. I could not pull the wire-nut connections out through the small hole and thought I would have to pull the whole oven out of the wall to acess the connections from the back so instead I clipped the wires close to the old sensor and connected the new sensor with the sma ll wire nuts provided, then enlarged the hole in the oven wall, being careful not to pinch the wires then pushed the wire nuts and extra wire back through the hole and put the screws back in the flange.
Read less
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More