KTM3380A Frigidaire Range - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Took out the old & easily replace it with the new set. No tools required.

Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a minute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back.

Just to point out the pans were delivered within a few days which was very quick. I just dropped them in. They fit perfect. Thank You for no stress.

I first unplugged the power cord and raised the range top and shut off gas supply to oven. then i removed the broiler drawer. Then using the adjustable wrench i loosened and removed the gas supply line from safety valve. Then using the philips head screw driver i removed the 2 screws holding the heat sheild surounding the valve. Then i unplugged the 2 wires on the valve body. then i removed the 3 screws from valve bracket and removed the valve. Install in reverse order and adjust gas orfice for proper burner flame using adjustable wrench. takes about 30 mins. I have done this repair once befor so i kinda knew what i was doing from the get go!!!! I had the new part i had ordered from this site in just 3 days!!!

I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

No installation steps required. I did have very fast delivery of parts ordered.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

This hard to find GE part number was easy to find at PartSelect.com. The GE dealer said the part was permanently out of stock. Lift lid and remove a few screws and pull off two wires and replace switch plate and reconnect everything. Good to go.

I determined the safety valve must be defective. The model number of the Okeefe-Merrit/Tappan/Frigidaire/Electrolux stove (27 yrs old) could not be found online nor at Frigidaire's parts call center. However, due to Partselect's most helpful picture parts pages, I was able to find my valve with the part number clearly showing for me to see. No picture, no resolution. The info sheet with the part was beneficial and placement time was 15 minutes.

I raised the cook top and removed the fuse in the back, right corner and shut off gas at front left corner. After using meter to be sure there was no power, I marked the wires as front and back, disconnected them using needle nose, disconnected gas line using two wrenches, removed three screws in retaining bracket before sliding unit out. Installation was the reverse.

With fuse replaced before installation I measured 120 volts across the two wires. (Don't try to do it hot.) When attached to the valve the measure went down to 2.9 volts. After installation and all restored, it took about 1 to 1 1/2 minutes for ignition.

I may have saved myself the purchase of a new stove just now, but after 27 years I think she is going to want a new kitchen. It was worth the repair and Partselect was prompt with the delivery. Happiness returns to a disgruntled cook.

Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

remove screw, remove burner, install new burner and screw

No Problem, couldn't find them at any local repair facility so I looked on line and found them here, ordered 4 drip pans and the exact replacements came within a few days.