Models > FPGH3077RFA

FPGH3077RFA Frigidaire Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for FPGH3077RFA

Viewing 7 of 7

Manuals & Guides for FPGH3077RFA

Click to download
Keep searches simple, eg. "belt" or "pump".
CAP
$24.35
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills. The surface burner cap is located on the top of the burner head and is used in ranges ...
In Stock
$48.85
In Stock
CAP
$30.07
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
In Stock
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
In Stock
In Stock
$11.77
This is a screw for your range or microwave. This part is sold individually. It has a pan head, a pointed tip for use with sheet metal, and an x-shaped drive. This screw is a #8, has 18 threads to the...
In Stock
CAP
$35.49
Sold individually.
In Stock
CAP
$37.89
In Stock
In Stock
Sold individually.
In Stock
$18.22
In Stock
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for FPGH3077RFA

Viewing 5 of 5
Oven is too hot
Fixed by these parts
Fixing
How to fix it
Oven not heating evenly
Fixed by these parts
Fixing
How to fix it
Little to no heat when baking
Fixed by these parts
Fixing
How to fix it
Element will not heat
Fixed by these parts
Fixing
How to fix it
Gas smell
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
John from Stevensville, MD
Parts Used:
318398302
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
replacing the fan on a convection oven (fan was making a vibration noise)
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. O nce there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.
16 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from NEVADA, MO
Parts Used:
5304504897
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Top oven overheating
Have a double wall oven and the top oven would not shut off or broiler part would stay on and burn tops of food. Since bottom oven was not having any issues felt like it could
Not be control panel so decided to try the temp sensor. Since replacing oven has worked properly.
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
john from PITTSFIELD, MA
Parts Used:
5304504202
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Original Meat Probe insulation separated on the probe end
I searched the web for a replacement and Parts Select had a picture and part number for the exact same probe. I ordered the probe and it arrived very quickly. The problem was that the probe I received didn't match the picture as shown on the web site. Instead I received a probe that was a different color and the actual probe was about 2" shorter than the one I was replacing. I called customer service and was told that the probe I received was the new version that the older version was discontinued. If they had updated their pictures on the web site I would not have ordered the probe. Parts Select customer service did apologize for the issue and offered to have me return for a refund.

I will order from Parts Select but I will call first to verify that the item pictured is the actual item being shipped. Parts Select please update the part pictures to show the actual items being sold.
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!