FGF318GCA Frigidaire Range - Instructions

Initially, I tested the temperature sensor and it was OK. I pulled out the range and shut off the circuit breaker to it. I removed the upper back sheet metal panel to expose the clock timer. I removed the 4 screws to it, unplugged the wires to it and plugged them into the new clock timer. I carefully removed the plastic facing stuck to the face of the old clock timer and stuck it on the new clock timer. No new adhesive was necessary. I placed the newly connected clock timer in position and secured it with the 4 screws that secured the old clock timer. I pushed the range back into position and reset the circuit breaker. I turned the oven on and the problem was resolved.

I am an HVAC tech by trade so it wasn't difficult to diagnose problem with safety valve. The hard part was being without an oven for a week. Repair was simple and effective--oven works good as new.
Shut off gas and unplugged oven. Removed floor of oven between broiler and bake section, used wrenches to disconnect gas line from safety valve in back of oven, used philipps head screwdriver to remove burner assembly and gas valve, reversed process to replace. Checked out operation--OK.

Turned off power, took back off stove removed old probe.
I had to splice wires since new probe ends did not match up.
the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wires.
After waiting, I turned the breaker on and my range came back on.

One day my wife turned on the oven and it didn't get hot. The heating element was cold even after it was turned on for a few minutes. The same story with the broiler. The stove top and timer worked fine, you could turn the oven on, it just never even started to heat up.
I ordered the new clock assembly and it got to my house in 2 or 3 days.
Once I got the new clock assembly, it was pretty easy to put in. Just take the back panel off (6 screws), unplug 5 or 6 wires, and 2 more screws and the old clock assembly is out. I peeled off the face sticker from my old clock and stuck it on the new one.
Putting it back in was just the reverse of taking the old one out. 2 screws, plugging in the wires, and then putting the back panel on.
Its been working as good as new for over a month.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

took upper back of stove off then removed 4 screws and replaced timer---that simple

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Unplug range, remove oven racks, remove 2 screws at the rear of oven bottom sheet metal panel. Lift the back of the panel and slide to the rear a little , then remove panel. Remove nut on top of heat shield and remove shield.. Open broiler draw slightly Note wire connections to gas valve. Remove Philips head screw from sheet metal guard bottom left rear to access wire connection. remove 2 hex head screws the hold igniter in place and install new igniter. remove spade connectors from gas valve and connect spade connectors from new igniter. , remove molex connector from bottom left rear and connect one from new igniter..Install shield in left rear bottom. install heat shield over burner and install nut. Install sheet metal panel in bottom of oven and 2 rear screws.. install oven racks and plug range back in. set clock and test your repair.

Turn off the circuit breaker to range. Removed the back panel using a nut driver. Removed color coded wiring from old clocktimer and placed wiring on new clocktimer. Removed old clocktimer from range using a phillips screwdriver. Removed the white clock face using a utility knife, placed the white clock face on the new clocktimer. Installed new clocktimer in range using a phillips screwdriver. Replaced the back panel using a nut driver. Turn on the circuit breaker. Set the range clock to the correct time. Baked some cookies to test oven. Easy as pie :)

order pcs fit perfect.

One night I found a mouse living in my stove. We found it literally living underneath the top of the stove (the part where the burners are that you have to lift up). The insulation on the inside of the stove was literally covered with mouse poop, dog food, dog treats, and scraps of food among other things. It was totally nasty and I thought we would have to buy a new stove. However, I searched online and found replacement insulation on PartSelects website and ordered it. It was cheap and the fix was removing old insulation, vaccuming out and cleaning the stove then replacing the insulation with the new one. PartSelect had a great price and shipped promptly.

it was an easy repair, and i thought it was the clock /timer, but it was the probe.

Slide out the old; slide in the new!