FEF387XECA Frigidaire Range - Instructions

used a screwdriver pushed the old ones out put the new in. the video instructions were great.

Inserted new slide as directed by video. Very easy and video was very helpful.

Pulled broken one out, slid in the new. Most unbeliveable service I have ever received. Tremndous job, you should sell it to others, Many thanks

Frst I slid the drawer out.I then pryed the broken drawer glides off with a flat blade screwdriver. The new drawer glides then just snap into place,then reinstall the drawer and check for smooth operation.

The old glides were broken off so I didn't know I needed these glides until I saw the parts section of the Manuel. When they arrived I snapped them in with no effort at all.
P.S. The shipping is fantastic here......i ordered on Monday received them on Tuesday. Now that's shipping:>)

The two back door glides were missing and broken (one of each), and needed to be replaced. Finding the parts online was MUCH easier than I expected,and the repair was remarkably simple. Parts snapped into place, the drawer had to be lined up, and it slid right into place. Very easy!

It was so easy my wife did it bu snapping in the new clips.

Turned off power, took back off stove removed old probe.
I had to splice wires since new probe ends did not match up.
the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wires.
After waiting, I turned the breaker on and my range came back on.

This was very simple I just snap the part on no tools required. it took less than 2 seconds.

I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet metal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the different sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

Removed the back cover of the range. Removed the knob from the front of the switch. Removed 2 screws holding switch to range. Removed wires one at a time and connected to proper poles on replacement switch and reinstalled new switch on range

First my husband cut off the circuit breaker. He then removed the two screws that held the element in place and pulled the element out about 3 inches and disconnected the two wires. The rest was easy. We were impressed at how fast the element was sent. We were told about 5 days to 7 days. The element arrived on the second day. Very please with the service and the product.