MEF301PBDC Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeanette from Alpharetta, GA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front slide of bottom drawer broke off.
Inserted new slide as directed by video. Very easy and video was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph D. from Stuart, FL
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide
Pulled broken one out, slid in the new. Most unbeliveable service I have ever received. Tremndous job, you should sell it to others, Many thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from North Salt Lake, UT
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Baking Heating Element Burned Up
Used a screw driver with a socket head to remove the two hex head screws holding the old element. Pulled the old element forward until the two wire attachements were visable. The wires were attached with a simple tab connector. Removed the wires from the element. Attached wires to new element slide the element and wires back into wall of oven and replaced screws. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Spring Valley, AL
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Cord was not tightened enough by delivery crew.
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWARD from ONSTED, MI
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
plastic clips were cracked.
It was so easy my wife did it bu snapping in the new clips.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Poulan, GA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke drawer glide
This was very simple I just snap the part on no tools required. it took less than 2 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from washington, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
blown bake element
Removed the two screws that hold the element in place at the rear of the oven.Unplug each prob,you may need pliers as they can be a little tight.Reconnected the new element.Keep the old screws.New element does not come with screws.Always unplug range when doing repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from New Port Richey, FL
- Parts Used:
- 5303935086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
High heat reluctant to turn down.
Most of the job is simple fastener mechanics.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Use a nut driver or Phillips screwdriver. Remove rear panel.
Pull out control knob. If it is stuck, wrap a small rag around the back of it and pull the rag steadily.
Carefully match marked terminals on the replacement switch with those on original. Switch terminals may not be in the same location. Replace wires one for one, one at a time.
Carefully select the correct knob filler for the switch post. Several are supplied. Proceed with logic and measure the shaft length and the filler length and type to match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ana from Miami, FL
- Parts Used:
- L304430992, 316048413
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had used generic drip pans that did not fit right
Ever since we moved to this house I had used generic or standard drip pans found in any store. Needles to say they never fit properly so I always ended up with some burners tilting so my food would not cook evenly Until I decided to search for stove specific drip pans and this is how I bumped into your site. I am so happy now I can use all four burners at the same time if I wanted to, and my food cooks evenly since the burners are not tilting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Homer from Thomaston, GA
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drawer glide on bottom stove drawer broke
Snapped the new part into the slot the old one had been in.The repair including opening and closing the drawer took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Flatwoods, KY
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Element went out in 20+ year old oven
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the element and put back in place. Took about 10 minutes. Repair part came in 2 days. Very awesome website!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Attica, MI
- Parts Used:
- 5303935086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Right front burner would over-heat
First of all I removed the top panel then removed the switch. I then took pictures of the switch & drew a sketch with all the info. Then I went to your web site, matched up the switch & ordered.
When the switch arrived I went thru the above replacing the bad switch.
When the switch arrived I went thru the above replacing the bad switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from hollywood, FL
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
corroded terminals
was more of a job of splicing wires together than anything else. Loved the heat shrink electrical tubing
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
to put over the wires for insulation. used a hair
dryer. must buy more of that amazing stuff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Lebanon, IN
- Parts Used:
- 5303935058, 316442300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner quit working
pull out old burner, lifted range top change the terminal which took about 5 min. close top put new burner in and was ready to go. works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALLAN from APACHE JUNCTION, AZ
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing oven racks
order pcs fit perfect.
Was this instruction helpful to you?
Thank you for voting!