TGP310KW0 Estate Range - Instructions

I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 if not more. we are very very happy with our decision to replace the part ourselves unstead of spending extra money we didnt have .

Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover

Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together.

I just unscrewed the old one out, which was 2 screws and screwed this one in. But the thing that was best of all was how fast the part came in. It literally came the next day.

Having no manual nor finding any instructions online, I spent a while trying to figure out how to safely get to the ignitor mounting screw under the range top. I popped the snap clips on either side of the stove to loosen the top and pulled the top up a few inches to see why it was being difficult to raise. It turns out that the gas piping was solidly attached from the controls to the burners and I was slightly bending the tubes as the top was raised. The tubes have angles and curves to "accept" the bending pressure I was applying, so it looked like I was doing the right thing. In case I was not doing the right thing, however, I raised the top only enough to get access to the ignitor base and mounting screw. Then the fun began as the screw would not loosen. After several attempts using liquid wrench, tapping on it, etc., the screw head finally just broke off. Uh-ohhhh. Not to worry, however, as there was an empty mounting hole right next to the old one that appeared to be able to work. The mounting screw for the new ignitor was backordered, so I tried a couple dozen different screws I had in my toolkit and finally found one that would fit width-wise, but I had to nip off some of the length to get it to seat properly. The replacement ignitor also had a different width blade connector than the original so I had to grind away some of its width to reattach it to the lead wire. If I had a different sized blade receiver, I would have instead replaced the receiver on the end of the lead wire. It took about 90 minutes in all.

I had already removed the 2 plates in the bottom of the oven to take an initial look. After not finding anything obvious, and searching on line for advice, I ordered the igniter. After the igniter arrived it was a matter of removing 2 screws, pulling out the lower drawer to gain access to the igniter disconnect, and done.

thanks for getting the correct part to me so quickly. Also the diagram and part number search was right on the money!

Installing the part was really easy. I first turned the gas off, simply remove two screws tht hold the igniter in place. I then remove four screws from the back panel and disconnected the part. The feedback from other users on your site made me realize how easy it was. It took less than thirty minutes.

Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Removed the panels, disconnected and dismounted the igniter and installed the new one. Pretty simple.

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

Part came super fast, remove and replace two screws - nothing to it

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Amazing after two years off frustration due to unsurety of problem went to your site found part problem in question that matched my problem.two screws and a plug now im burning like im supposed to.success