RLS270UW (P1143149NW) Caloric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lansing, MI
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from GLOVERSVILLE, NY
- Parts Used:
- Y07491300
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Oven Would Not Light
Removed the defective igniter, removing one screw and disconnected wire, replaced new ignighter in reverse fashion. And WELLA! The old oven works again!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth Coates from Washington, DC
- Parts Used:
- WP314647B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
loss burner grate
Just set in the new grate and start cooking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Perth Amboy, NJ
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from RIVERSIDE, CA
- Parts Used:
- 8009
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Las Cruces, NM
- Parts Used:
- WP4157180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
two burner ignitors would not function on cook stove
1. ordered two new switches
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lake George, CO
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from montgomery, NY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
No leveling legs
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve
Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Frankfort, KY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Shelton, WA
- Parts Used:
- 31829601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
One day all the burners just started sparking without being turned on.
Pulled the power cord, and of course it stopped sparking. Removed the protection cover, I then removed the upper and lower screws with a screw driver. Pulled the module out so I could work. I removed the leads one for one with the new module just to made sure I did mix them up, and replaced the screws on the new module, but found that there were two clips on the setting surface of the new part that needed to be clipped off with side cutters in order to set flush. completed the installation of module and protection cover.
It beats a service call. GB
It beats a service call. GB
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!