Models
>
P1141140NW
P1141140NW Caloric Range
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$24.10
This square chrome drip pan is intended for use with gas ranges. With a 4 inch diameter center hole and 7-3/4 inch sides, this pan is dishwasher safe and comes one to a package.
In Stock
Order now and your part arrives by Mar 21
In Stock
Order now and your part arrives by Mar 21
This gas burner grate is used for some gas ranges and cooktops. This is a black burner grate with each side measuring almost eight inches.
No Longer Available
This is a genuine OEM replacement part. This surface burner ignition switch is commonly used on ranges, wall ovens, cooktops, and microwave oven combos. When the gas burner valve is pressed this is th...
Special Order
$20.95
This is a genuine OEM replacement part. This nut is used in a number of appliances. Most often it can be found in the assembly of ranges, air conditioners, cook tops, washers, microwave oven combos, r...
Special Order
This single oven door side seal is fourteen inches long. It is made of black rubber and it has a metal hook in each end.
No Longer Available
The color of the original part or the part you receive may be different from the pictured part. This is still the correct part.
No Longer Available
This is an OEM part sourced directly from the manufacturer. This bake or broil spark igniter, also known as a spark electrode, is used in ranges and wall ovens. This electrode is used to help ignite t...
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for P1141140NW
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diana from Jacksonville, FL
- Parts Used:
- 31829401
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
electric ignite gas stove kept clicking the ignitor unless unplugged from electrical outlet
I removed the 2 screws that held the housing on at the back of the stove. Then I removed the 2 screws that held the module to the back of the stove. Since I am not an experienced electrical person (I am a female nurse in the operating room), I unplugged 1 wire at a time from the old module and plugged it into the new module. I repeated th
... Read more
is step with each wire to make sure I didn't put the wrong wire on a wrong spot until I had all the wires to the new module. Then reattached the screws, plugged in the oven and presto, it works just fine! Was amazed at how easy it was. A 50 dollar part instead of a new 1500 dollar stove. How easy is that?
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lansing, MI
- Parts Used:
- WP4157180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that atta
... Read more
ch to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Read less
Was this instruction helpful to you?
Thank you for voting!