Models > HGIP056UC/01

HGIP056UC/01 Bosch Range

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Elecrtrode – Part Number: 00631633
$23.76
This burner igniter creates the spark needed to light the surface burner. Made from ceramic and stainless steel, it’s built to withstand heat and wear. Replace it if your burner won’t ignite. Always u...
In Stock
Order now and your part arrives by Mar 19
SHELF – Part Number: 00798845
$66.25
This wire oven rack provides a stable, flat surface for baking, roasting, and cooking, ensuring even heat distribution throughout the process. Designed for durability and a precise fit, it helps organ...
In Stock
Order now and your part arrives by Mar 19
SLIDE – Part Number: 12024638
$130.95
This push-to-open slide kit restores smooth, handle-free operation to warming drawers. It’s designed for select Bosch, Thermador, and Gaggenau ranges and allows the drawer to open and close with a gen...
On Order
LAMP – Part Number: 00623710
$6.26
In Stock
Order now and your part arrives by Mar 19
Rubber Feet - Kit of 4 – Part Number: 00637940
$52.99
In Stock
Order now and your part arrives by Mar 19
SENSOR – Part Number: 00630873
$48.87
This genuine temperature sensor ensures precise heat regulation inside your oven for consistent cooking results and improved safety. Designed to measure the oven cavity temperature, it communicates wi...
In Stock
Order now and your part arrives by Mar 19
IGNITER – Part Number: 00755058
$108.38
This hot surface igniter helps light the gas burners in select ovens and ranges, ensuring quick and efficient ignition. It supports safe and consistent heating, and replacing a worn igniter can restor...
In Stock
Order now and your part arrives by Mar 19
SENSOR – Part Number: 00642855
$58.09
In Stock
Order now and your part arrives by Mar 19
SCREW – Part Number: 00612818
$6.26
In Stock
Order now and your part arrives by Mar 19
Cooktop Burner Cap - Black – Part Number: 00631625
$34.09
This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
In Stock
Order now and your part arrives by Mar 19
Range Surface Burner Cap – Part Number: 00631626
$37.51
This burner cap is for cooktops. Burner cap fits on top of the burner head. The burner cap protects the burner head from spills and helps spread out the burner flame for even heating.
In Stock
Order now and your part arrives by Mar 19
DISPLAY MODULE – Part Number: 12029207
$212.95
In Stock
Order now and your part arrives by Mar 19
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for HGIP056UC/01

Viewing 4 of 4
Will Not Start
Fixed by these parts
Fixing Fixing
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
Fixing
How to fix it
Oven is too hot
Fixed by these parts
Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jeffrey from Bloomington, MN
Parts Used:
00755058
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Igniter replacement
Getting to the igniter is trivial, only requiring the removal of the stove bottom (two set screws) and a heat shield (the heat shield is held in place by screws with size 20 star-driver heads). At this point a splice could be made to the original wires, IF ceramic wire nuts were included with the replacement igniter (but, alas, they are n ot). IF a splice were made the repair would be a very easy, 10-minute job.

To replace the igniter then requires the complete removal of the back of the range (17, size 20 star-driver, screws, if I remember correctly), plus the removal of an additional heat shield (one more screw). Then one must carefully lift and free the back from tabs on both sides that are set into slots. (Oh, and you probably want to loosen the electrical cord shield that interferes with the back coming off.) The new igniter wire plug is only then very easily re-attached to existing harness. Everything is then replaced to finish the repair.

None of this is difficult, if you don't mind moving your range away from the wall and dealing with on the order of 20 screws. Personally, I think I would have rather found an igniter with ceramic wire nuts to splice to the original wires (certainly not as elegant as replacing igniter and wires entirely, but far quicker and easier).
Read less
14 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jaymie from Intercourse, PA
Parts Used:
00642855
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Oven heating temp not turning off at set temp/overheating
Removed the wall oven to access temp probe connector strapped to the back of the oven. removed 2 screws holding probe inside the oven & replaced. Searched for the "fixing kit" thermostat part I was suggested to replace along with the probe. No thermostat type part was found in my oven, even though Bosch says it fits "somewhere". Reinstall ed the wall oven & tested. The temperature is working normal now. Will return the fixing kit.
Read less
9 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barry from MONROE, NY
Parts Used:
00630873
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven was not heating properly
Took the one out of the box and take off the back plate and detach the sensor
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More