ARH664E-P1130981NE Amana Range - Instructions

First I turned off the circuit breaker on the house electricity panel. I removed the two screws that held the element in place in the oven. There were two wires connected to the element by spade plugs that were free floating in a fiberglass pad. I reconnected the spade plugs and put the element back in place and put back in the two screws. This procedure had I known what I was doing could have been done with the stove in place and would take no more than 5 to 10 minutes. Having no experience at this, I had pulled the stove out into the room and also removed the back cover which turned out to be unnecessary. I put everything back in place and held my breath and turned on the circuit breaker. Voila! It worked!

un-screwed 2 scrws and pulled out the old one and pulled off the 2 wires put the new one on the floor of the oven and hooked-up the 2 wires and pushed it in the back wall and replaced the 2 screws! done maybe 5 minutes

Purchased 2 piece broiler pan from this site

Turned off the power! Unscrewed the element (2 screws) pullled the wires out. Put the new part right in. Easy!
Thank you-only a week before Thanksgiving, what a life saver! Also, order on Monday AM and was delivered by mid-day on Wednesday!

Regarding my right side oven door hinge replacement, P/N PS2172201

After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.

Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.

Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.

The hardest part was the two screws (they were baked on I guess). We turned off the breaker, put paper towels in the oven carefully sprayed wd40 on the screw. Waited about 5 minutes unscrewed the two screws, gently pulled out the plate. When you pull the two wires out there are two contacts. Look at the direction their on. Slide them off put in the new unit to the contacts, gently slide back in and put the two screws back. It was really that easy and I had no idea what I was doing. No need to pull oven out can all be done for the front side.

My bottom oven didn't work, and I had called a service to come out and fix it. It was a $60 charge just to come out. My friend owns an apartment complex, and she told me it was two screws and a pull to remove the element and replace. I took the element out, ordered it for $38, had it the next day and repaired my oven in a matter of minutes. It was so easy and inexepensive. I feel like I can do anything!

Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.

I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all together. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.

we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

Received part after one working day and was installed
in five minutes.. Would recommend as a do it your self
project with the support of PartSelect.com

left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge.
Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.

Lifted the top of the range, removed two screwsand old arm. Set the new arm in place with the two screws .

The lower element had burned out but in the process, it developed a short from line to neutral. Since the short was located about 3/4 of the total length from the one hot leg (L1) and the other hot leg (L2) was the relay controlled leg, there was a current path that allowed the element to heat even with L2 disconnected by the relay. Actually replacing the element was easy, just remove the back cover(s) and the element mounting screws (2) inside the oven cavity and the new unit slides into place. Reconnect the two wires to the new element and replace the back covers. Back in business and the cookies are coming out perfectly!

I took out ruined racks. Cleaned the oven, getting rid of all the melted plastic. Once oven was sparkling clean, I slid in the new racks I bought from here. (The easiest part).

* * * *
I'm very thankful to have found this site. My oven has been "out of order" for over 3 years. It's so nice to be able to use it again! =)