ACS7270AB0 Amana Range - Instructions

First I turned off the circuit breaker on the house electricity panel. I removed the two screws that held the element in place in the oven. There were two wires connected to the element by spade plugs that were free floating in a fiberglass pad. I reconnected the spade plugs and put the element back in place and put back in the two screws. This procedure had I known what I was doing could have been done with the stove in place and would take no more than 5 to 10 minutes. Having no experience at this, I had pulled the stove out into the room and also removed the back cover which turned out to be unnecessary. I put everything back in place and held my breath and turned on the circuit breaker. Voila! It worked!

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

My husband replaced the bake element in moments. We couldn't get the broken light out of the socket because we couldn't locate our needle nose pliers. After a few days I finally got tired waiting and found a small pair of pliers in the house and got the remains of the bulb out and screwed it in, and plugged it in and we're in business!
Never wait for a man to do what you can do yourself!
I was so pleased that ordering the parts on-line was so easy and I didn't have an expensive repair bill to pay!

Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws holding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.

Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.

TURN OFF POWER TO RANGE AT FUSE BOX -- a)Open the oven door, b) Unscrew the left and right silver nuts (not the black screws)that are in the oven under the control panel, c)pull off the four control knobs on the control panel, d) gently tilt out the control panel, e) set the control panel in/on the protruding arms, f) pull off THE connectors at the back of the switches - remember which is top and bottom, g) use a screw drive to break off the plastic pieces that hold the switches in place, h) push out the old switches, i) push/snap in the new switches, j) reconnect wires, replace control panel and screw in the nuts.

Purchased 2 piece broiler pan from this site

un-screwed 2 scrws and pulled out the old one and pulled off the 2 wires put the new one on the floor of the oven and hooked-up the 2 wires and pushed it in the back wall and replaced the 2 screws! done maybe 5 minutes

This is a very easy repair as the sensor had 2 screws and slid out of the back of the inside of the oven just enough to hook up the new one. I never had to back the oven out of the wall. It is a 5 minute repair. Ok I did use my son's head lamp from scouts for better light as you have to kill the power to the oven, so no oven light. And you can't hold a flashlight and do this alone.

However, I ordered the part before I took the old part out. Don't do that. There are 2 froms of Temp sensors that you can order one male and one female. I did not know that and just ordered what looked to be the right part. It turned out that I needed the female sensor. When I called the folks at part select they were terrific! They sent out the new part the next day and a UPS form via email to send the other part back.

I don't know what a service call would have been but this was very easy. I will go here first for appliance parts. Women can fix stuff too!

First turn off the electric breaker, and if necessary mark it or lock it so it will not be turned on while working on the unit.
I raised the glass stove top (it is hinged in the back), and propped it up with a piece of wood.
Removing the control requires the removal of a metal shield along with several mounting screws.
several wires needed to be removed, so I drew a diagram to make sure they all went back on the same terminals.
Reverse the order in replacing the control, and be ready for another 3 to 5 years of service.
This control is a universal part used on many different brands of ranges. Make sure you get the correct part before attempting this on your own because most parts supplies will not allow a return on an open electrical component.

I removed only 3 screws that allowed me to lift the glass top on the stove. I removed the burner and I could see where it short circuited. I ordered the new burner element. After it arrived I replaced it by moving the wires from the old element to the new element, and put it back together.
I am sure that I saved at least $200 in "labor".

first I unplugged the stove,took the screws out of the pan that holds the element to the stove, then unplugged the element.then I plugged in the new element, then screwed the screws into the pan that holds the element into the stove. it was very easy.

Turned off the power! Unscrewed the element (2 screws) pullled the wires out. Put the new part right in. Easy!
Thank you-only a week before Thanksgiving, what a life saver! Also, order on Monday AM and was delivered by mid-day on Wednesday!

Pulled stove out and unplugged it (energized wire at burner even with burner turned off) Removed screws to lift cook top Removed burner support brace Removed three screws to remove burner Removed connections from old burner, installed on new burner Replaced screws in burner to brace Replaced burner brace Lowered cook top and installed screws Plugged in stove and pushed it into space

Turn off the circuit breaker for the range. Raise the cooktop and prop with 14" 1x2. Remove the 3 Phillips head screws from the heat shield. Disconnect the ribbon cable connecting the touch pad to the ERC. Remove the 4 screws holding the ERC. Pull away the ERC. Remove the 4 screws holding the touch pad and remove the touch pad. Place the new touch pad in the space vacated by the old one and attach with 4 screws. Attach the ERC with 4 screws. Connect the ribbon cable from the touch pad to the ERC. Replace the heat shield and attach with 3 screws. Lower the cooktop. Restore the power to the range.

Regarding my right side oven door hinge replacement, P/N PS2172201

After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.

Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.

Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.