ALY1680BDS Amana Range - Instructions

Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.

remove 2 screws that hold element in place, remove element, replace with new element, and replace screws , replaced burner assy on other

I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.

Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.

Just used a car oil filter band type wrench and rotated the sealed burner cap a 1/4 turn. cleaned up the rust and dirty. Replaced it with the new cap and tightened it with a 1/4 turn by hand. Instruction can be found on Maytag gas installation manual. The burners are working well and just like a new range.

With a family of five a needed an extra oven rack as my RV oven is very small. After much aggravation between calling and going online to the manufacturer I still could not get any help. Even with locating the all important parts number. I was just about to give up when I was surfing around and found this website. Wow! What a relief! Not only did you show my where to find the part number, but I ordered it and got it within days. I spent more time on hold and online with the manufacturers customer service than anything else. From now on, no matter what I need, whether RV or home, I'm going staright to PartSelect. Thank You and my family thanks you too, as we wil be camping on Turkey Day and now I'll be able to get all the meal done at once! Happy Thanksgiving! God Bless

very easy to push each grommet into range top holes

I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.

Had to turn off the propane, disconnect the propane line and then remove several screws holding the stove in the cabinet. Once I was able to pull the unit out of the cabinet, I had to remove several other screws for the sides in order to gain access to the hinge arm and spring. The front of the oven door had to be removed in order to get to the hinges. Replaced both left and right hinges, hinge arms and springs. After replacing all of the screws, I reinstalled the stove into the cabinet and reinstalled the screws securing it to the cabintet. Reconnected the gas line and checked for leaks. None found. Oven door operates properly now.

just turn the burners counter clock wise with the help of a jar opener pad. unplug the wire connectors and replace the burners no hassle, no problem. Everything went fine… one thing though, it is not the same color as it was before. I didn’t realize it until opening the box. Previous color was grey. My wife is Ok with it, so I won’t complain, but maybe you should add the color option if there is more than one choice.

Best regards.

Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.

Unplugged the burner heads from the wires, and simply put the wires on the new burner heads and put back onto the stove,. Simple as pie. Very happy that i found parts select online, easy to find the part though your pictures and easy to order.
Loved being able to do this myself without a middle man. Very satisfied!

Opened oven door, slid in rack , closed door...
Fit perfect....

Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.

installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.