GBK24CB Amana Range - Instructions

Unplug the power cord from the unit. Remove the lower front panel; then the upper front panel including the door (unplug wire to door switch). Then remove the cover on the fan housing. Need to block the motor from turning; I used a stick to jamb the front of the motor; then unscrew the old blower fan and screw on the new one. Then replace the cover and put front panels back on.

Because the wheel had stopped and the shaft kept turning (junk from child's pocket got in there), the nut stripped itself away from the wheel causing low RPM and low air movement (lazy flame, vibration and clothes not drying)

I had to use a screwdriver to break the wheel away from the center nut and remove the fan. I then removed the air fan housing (3 bolt behind the fan wheel). I used a small pair of vise grips to hold the motor shaft staionary while I used a pair of channel lock pliers to remove the nut that was molded into the fan from the motor shaft. It was harder to get the nut started then I would have thought.

Once complete, I put the fan housing back on and threaded the new wheel on easily. The motor has external fins on it which turn with the shaft-I held one lightly while I threaded the fan on to keep the shaft from turning. Tighten just slightly more than hand tight-don't go crazy-it's threaded to stay tight with rotation. Works great and very quiet now.

Purchased 2 piece broiler pan from this site

I removed the 2 screws that held the housing on at the back of the stove. Then I removed the 2 screws that held the module to the back of the stove. Since I am not an experienced electrical person (I am a female nurse in the operating room), I unplugged 1 wire at a time from the old module and plugged it into the new module. I repeated this step with each wire to make sure I didn't put the wrong wire on a wrong spot until I had all the wires to the new module. Then reattached the screws, plugged in the oven and presto, it works just fine! Was amazed at how easy it was. A 50 dollar part instead of a new 1500 dollar stove. How easy is that?

Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.

The knobs were a perfect replacement and I just slid them onto the posts on which the old ones were on. Although my range is a Glenwood I think that the parts are now made my Whirlpool (not exactly sure) but they are a perfect match. My order came so quickly and I am thrilled with the transaction. I didn't think I would ever find the replacement knobs and thought I might have to get a new range as you could not read the oven temperatures at all on the old knobs.

Removed the defective igniter, removing one screw and disconnected wire, replaced new ignighter in reverse fashion. And WELLA! The old oven works again!!

This was my first time repairing a dryer. If I knew when I started the project what I know now, it would have been an easy repair. First, you should know that the series number (used for selecting a wiring diagram) is the last two digits of the unit's serial number (not model number). In my case, the series number was 11. The hardest part for me was figuring out how to take the dryer apart. I made the mistake of starting with the top instead of the front. In fact, I removed the control panel and disconnected all the wires, labeling them carefully, and creating a diagram, so i could put it all back together later. I now realize I could have left that all together and just lifted the top up in the front without removing it. That knowledge would have saved hours of work, so I hope it helps someone (prop up the front a few inches and start by removing the panel on the lower front, then remove the screws on the main front panel, and then pull out the bottom of that panel toward you until the top of that front panel disengages from the top of the dryer - the rest is obvious). So it turns out there were two separate problems: 1) the blower wheel had broken completely off of the motor so it wasn't spinning - this is why hot air wasn't being pulled through from the heater in the back of the dryer; 2) the pulley on the spring-loaded lever arm attached to the motor was squeaking due to lack of lubricant. So the solution was to replace the blower wheel and spray WD-40 in the pulley (and also, for good measure in the roller bearings that support the drum in the back of the dryer). Most of the time spent on the repair was just due to my own mistakes. In particular, once I got everything back together after the repair, it stopped squeaking and there was good airflow, but it wasn't heating. I spent an entire day trying to troubleshoot the lack of heat. I tested and bypassed all of the thermostats and heater fuses and the heating element still wouldn't come on. I even managed to accidentally ground one of the leads from the fuse and had to replace a melted wire connector (trip to the Shack). In the end, it turned out that a wire which had been accidentally disconnected from the main power cord to the dryer, I had put back in the wrong spot. There is L1, L2, and neutral going into the dryer. I had the heater on the same circuit as the motor and other stuff. Once I traced the wiring diagram back, I realized this and corrected it by putting the heating circuit back onto L2. Now it "hums like a Singer". If everything had gone smoothly, instead of being a 2-day repair, it would have been a 2 hour repair. 2 hours instead of 1 because to get the leverage I needed to remove the old blower nut, I had to actually pull the motor assembly out of the dryer and move it to my workbench. Someone who is strong or more limber or has better tools might be able to skip that step, reducing the time by about 45 minutes. Good luck!

Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.

1. ordered two new switches
2. installed switches
3. all ignitors work

Really appreciated the pictures of the parts--made selection very easy.

I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.

After removing the lower access panel, I observed the drum and belt and saw it turning freely. The support rollers in the back turned freely and were in good condition as well. At odd intervals the unit made a humming or grinding noise, and i decided to check the blower wheel (the other rotating part in the system). I found that the central hub of the wheel (which is made of a nylon like plastic) had sheared off from the wheel itself. I ordered a new part and started to remove the old wheel. **NOTE** many of the stories I read described how this part would have a reverse thread, it did not and that cost me an extra 30 minutes to figure out (the new part had arrows showing the correct direction to put on and remove - the original didn't). Once everything was cleaned and reassembled, I started the dryer again, but got no heat. I had previously replaced the heating element, so I thought my wiring was wrong. That wasn't the problem, but a hint from this site about checking the incoming wiring was the solution, my ground wire had come off the terminal in the back of the dryer and I wasn't getting the volatge across the element that it required. With the ground wire back in place, everything worked fine.

took frount off ,then filter, pulled drum out, then blower plate & spun impeller off. went back together easy ,except belt . that gave me a little problem but finally got it thanks

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find