968W-4CW Admiral Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Salisbury, NC
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
heat element wouldn't heat after 30 years of cooking
Pulled screws loose from element, pulled old element out and replaced with new..really simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tom from cincinnati, OH
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower element in oven not heating.
Removed, tested and measured the old element. Got on line to find the part and ran across Part Select. Ordered and received the part in three business days. It was an exact fit and in good order. The total operation including removal and replacement of the element, locating and ordering the part only took about thirty minutes.....and that includes the ten minutes it took me to find my #2 Phillips screwdriver! : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sanger, TX
- Parts Used:
- WP7212P003-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heat was escaping from my oven and really heating up my house
The heat sealing strips are elastic type material with hooks on each end. I simply removed the old strips and hooked the new ones in place.
It was easier than I ever dreamed possible!
And my kitchen is now nice and cool.
Pat Morrison
Sanger TX
It was easier than I ever dreamed possible!
And my kitchen is now nice and cool.
Pat Morrison
Sanger TX
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lebanon, NH
- Parts Used:
- WP7212P003-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace a side oven door seal
The trickiest part was making sure that the correct part was ordered. The first attempt was a failure. The seal was too long and the clips were too big.
After finding the correct part it was a breeze.
After finding the correct part it was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- andrea from new york, NY
- Parts Used:
- WP7212P007-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A seal came off the oven
I found the model, ordered the new seal, it arrived very quickly via mail and I replaced the seal. You simply slid off the old, slid on the new one and hooked it in place. No expensive repairman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from North Hills, CA
- Parts Used:
- WP7212P003-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door gasket broken
This part showed up so fast I couldn't believe it. Took longer to unwrap the package than to install the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from Georgetown, TX
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old lower element burned through, broke
found the element using visual grids supplied on the website. Measured old element and matched up with another after finding out that Whirlpool parts are interchangeable. Turned off power at breaker box. Replaced in 10 minutes.Fired it up to test at high temp for about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Dequincy, LA
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element burned out
Removed old element with philips screw driver, reninstalled new element in reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Abilene, TX
- Parts Used:
- WP7406P012-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element was corroding.
I turned breaker off for oven, removed screws from element mount, pulled the element out about two inches, then slid wire connectors up to unhook from element. Then set new element in, slid wire connectors on to back new element, then used pliers to make sure they were tight and secure by squeezing them, screwed element back in, turned breaker back on. Turned oven onto bake and left on for few minutes while it burned chemicals off element. Very simple!!
Was this instruction helpful to you?
Thank you for voting!