Models
>
UT80522A
UT80522A Homelite Pressure Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for UT80522A
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
This thermal release valve is for pressure washers.
Thermal release valve attaches to the pump and releases the water and high pressure inside the pump if the water temperature exceeds normal oper...
No Longer Available
$6.51
This is an OEM detergent suction kit, also referred to as a chemical injection kit, for a pressure washer. This kit is threaded into the pump assembly and is connected to the chemical siphon tube that...
In Stock
Order now and your part arrives by Apr 2
$6.51
Genuine OEM replacement part, this item is sold individually. This is the part on the pressure washer that you connect the hose to. The hose then connects to the handle assembly and spray wand.
In Stock
Order now and your part arrives by Apr 2
$38.32
(25 ft., 3000 psi)
This water hose is for pressure washers.
Water hose carries water from the pump to the spray wand.
Wear work gloves to protect your hands when installing this part.
In Stock
Order now and your part arrives by Apr 2
$36.01
This is an original manufacturer sourced replacement part used with Homelite pressure washers. This is the starter assembly that is used to crank start the unit. It includes a plastic shroud/housing, ...
In Stock
Order now and your part arrives by Apr 2
$6.51
It is a genuine replacement part that is supplied by original equipment manufacturer for use with Homelite, Ridgid and Ryobi pressure washers. This siphon tube is used to deliver the chemical solution...
In Stock
Order now and your part arrives by Apr 2
$6.51
This is an authentic OEM quick connect nozzle, guaranteed compatible with the Ryobi and Homelite machines listed below. This is a standard green pressure washer tip with a twenty-five (25) degree spr...
In Stock
Order now and your part arrives by Apr 2
$16.58
This is an authentic OEM part for pressure washers made by Homelite, Ryobi, and Husky. The inlet tube fits onto the pump and is made out of metal. When replacing this part a socket set may be needed. ...
In Stock
Order now and your part arrives by Apr 2
This is an authentic OEM nozzle made to fit the Ridgid and Homelite pressure washers listed below. As a standard sized white nozzle, this part features a forty (40) degree spray width. It is least pow...
In Stock
Order now and your part arrives by Apr 2
This is an authentic OEM sourced replacement part that is made for use with pressure washers. It is made of high-quality materials and is used to remove contaminants from the water that goes through t...
No Longer Available
$6.51
This is a genuine manufacturer-approved replacement part which is specially designed for use with Homelite pressure washers. The purpose of this gasket is to provide a tight seal between connected par...
In Stock
Order now and your part arrives by Apr 2
This item has been OEM sourced to ensure a high-level of quality. The fuel tank outlet is intended to be used with pressure washers from Homelite. This item attaches to the bottom of the fuel tank and...
In Stock
Order now and your part arrives by Apr 2
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for UT80522A
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jimmy from BURLINGTON, NC
- Parts Used:
- 099980425082, 099980425080, 099980425079, 099980425077
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
Fuel system damaged by allowing E85 gas to remain in tank.
Tank is held in place by 2 nuts and 1 bolt. These were removed and tank lifts off. Installed filter assembly and fuel hose to bottom of new fuel tank. You must install fuel hose clamp to tank connection before installing new tank. Install the other end of fuel line to carburetor on engine with other clamp and you are finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duarte from GRISWOLD, CT
- Parts Used:
- 308452002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Must have froze over winter (stored in garage)
Repair was easy, however had to u tube issue for proper orientation of parts as it did not come with any instructions. Wished I had two as shipping was twice as much as part. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from BEACH PARK, IL
- Parts Used:
- 17151Z4401100000, 099980425082, 099980425080
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Leaking hoses.
1) Loosen engine assembly from frame.
2) Remove fuel tank, hoses and disassemble other hoses and components.
3) Attach new hoses to carburetor.
4) Reassemble fuel tank, engine and carburetor components.
5) Re-center motor engine assembly onto washer frame and tighten nuts, bolts and washers as needed.
2) Remove fuel tank, hoses and disassemble other hoses and components.
3) Attach new hoses to carburetor.
4) Reassemble fuel tank, engine and carburetor components.
5) Re-center motor engine assembly onto washer frame and tighten nuts, bolts and washers as needed.
Was this instruction helpful to you?
Thank you for voting!