Models
>
HL252300
HL252300 Homelite Pressure Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for HL252300
Viewing 2 of 2
Keep searches simple, eg. "belt" or "pump".
This thermal release valve is for pressure washers.
Thermal release valve attaches to the pump and releases the water and high pressure inside the pump if the water temperature exceeds normal oper...
No Longer Available
$5.19
This is an OEM detergent suction kit, also referred to as a chemical injection kit, for a pressure washer. This kit is threaded into the pump assembly and is connected to the chemical siphon tube that...
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
$30.50
(25 ft., 3000 psi)
This water hose is for pressure washers.
Water hose carries water from the pump to the spray wand.
Wear work gloves to protect your hands when installing this part.
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for HL252300
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jimmy from BURLINGTON, NC
- Parts Used:
- 099980425082, 099980425080, 099980425079, 099980425077
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench set
Fuel system damaged by allowing E85 gas to remain in tank.
Tank is held in place by 2 nuts and 1 bolt. These were removed and tank lifts off. Installed filter assembly and fuel hose to bottom of new fuel tank. You must install fuel hose clamp to tank connection before installing new tank. Install the other end of fuel line to carburetor on engine with other clamp and you are finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duarte from GRISWOLD, CT
- Parts Used:
- 308452002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Must have froze over winter (stored in garage)
Repair was easy, however had to u tube issue for proper orientation of parts as it did not come with any instructions. Wished I had two as shipping was twice as much as part. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from BEACH PARK, IL
- Parts Used:
- 17151-Z440110-0000, 099980425082, 099980425080
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Leaking hoses.
1) Loosen engine assembly from frame.
2) Remove fuel tank, hoses and disassemble other hoses and components.
3) Attach new hoses to carburetor.
4) Reassemble fuel tank, engine and carburetor components.
5) Re-center motor engine assembly onto washer frame and tighten nuts, bolts and washers as needed.
2) Remove fuel tank, hoses and disassemble other hoses and components.
3) Attach new hoses to carburetor.
4) Reassemble fuel tank, engine and carburetor components.
5) Re-center motor engine assembly onto washer frame and tighten nuts, bolts and washers as needed.
Was this instruction helpful to you?
Thank you for voting!