Models
>
HPA158190901
HPA158190901 Powermate Compressor
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for HPA158190901
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$11.16
This is an authentic manufacturer-approved replacement o-ring, it is specially designed for use with Powermate air compressors. It helps to provide an air tight seal for the cylinder, please make sure...
In Stock
Order now and your part arrives by Apr 9
$74.19
It is a genuine regulator repair kit that is supplied by the original equipment manufacturer for use with Powermate electric air compressors. Unfortunately, over time components will wear out and may ...
Special Order
This is an authentic Powermate replacement part, sourced from the original manufacturer for use with air compressors. Pressure switches are used to start the motor to build pressure in the tank, then ...
No Longer Available
$12.79
This is an authentic manufacturer-approved replacement o-ring, it is specially designed for use with Powermate air compressors. It helps to provide an air tight seal for the cylinder head, please make...
In Stock
Order now and your part arrives by Apr 9
$33.41
This is a genuine OEM replacement part that has been sourced directly from Powermate. This tube is ? of an inch in diameter and it is 28 inches long. It is runs from a check valve to a discharge port....
On Order
Special Order
$43.62
The flexible transfer tube is made out of metal. This is a genuine Powermate replacement part used in compatible compressors. It is priced as an individual replacement part. A wrench might be required...
In Stock
Order now and your part arrives by Apr 9
This is a genuine replacement part sourced directly from the manufacturer. The metal screw is designed for use in many air compressor models. This part secures the top of the compressor shroud. Althou...
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
In Stock
Order now and your part arrives by Apr 9
$60.21
This is an original replacement part sourced directly from the manufacturer. The head is commonly found in Powermate air compressors. This part is made of metal, and is used to cover and secure the ...
On Order
$11.16
This is an original Powermate replacement part. The hubcap is commonly found on air compressors. This part is made of metal, and is used to secure the wheel to the axle. Please note that these hubc...
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from AUBURN, WA
- Parts Used:
- 033-0001
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
hubcap fell off my coleman air compressor
repair didn't happen the part was the wrong size so i wasted $20 and my time because the part was on back order (which the website did not show) Will never use you service again, complete waste of time and money
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ANAHEIM, CA
- Parts Used:
- 034-0192
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Air leak at pressure switch diaphram
Kobalt 15g compressor.
* unscrew 6 T-20 to remove compressor housing cover.
* disconnect 2x black wire and 2x wire, and 2x green.
* use hand torch (or lighter) to soften tubing.
034-0174 is a discontinued pressure swirch. Purchased 034-0192 which fit perfectly. Only difference between 0174 and ... Read more 0192 is the unloader valve. Which I did not need as its my unit is piped separately.
* unscrew 6 T-20 to remove compressor housing cover.
* disconnect 2x black wire and 2x wire, and 2x green.
* use hand torch (or lighter) to soften tubing.
034-0174 is a discontinued pressure swirch. Purchased 034-0192 which fit perfectly. Only difference between 0174 and ... Read more 0192 is the unloader valve. Which I did not need as its my unit is piped separately.
Read less
Was this instruction helpful to you?
Thank you for voting!