KSM6573CER1 KitchenAid Mixer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tina from Beverly, MA
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken wire whip for mixer
tossed the broken whip and replaced it with my new one. It took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kate from Vredenburgh, AL
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace a broken attachment for an ancient KitchenAid
I decided to repair my grandfather's first generation, ancient KitchenAid mixer. The wire whip had come undone so that it couldn't be used.
Everyone was skeptical that I could find the part for such an old mixer, but I got the serial number and googled "kitchenaid + the part number + whip whip + repair." That search brought up PartSelect.com.
It was very easy to plug in all the info and find the part on PartSelect.com and 24.99 later, the part arrived on my doorstep.
I took it out of the box, fitted it to the attachment on the mixer and turned the mixer on. Viola! Worked perfectly!
Thanks PartSelect! Everyone is amazed that I found the part for such an old appliance.
Everyone was skeptical that I could find the part for such an old mixer, but I got the serial number and googled "kitchenaid + the part number + whip whip + repair." That search brought up PartSelect.com.
It was very easy to plug in all the info and find the part on PartSelect.com and 24.99 later, the part arrived on my doorstep.
I took it out of the box, fitted it to the attachment on the mixer and turned the mixer on. Viola! Worked perfectly!
Thanks PartSelect! Everyone is amazed that I found the part for such an old appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Charlotte, NC
- Parts Used:
- WP9706885
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
The mixer would not raise the bowl
I removed the motor assembly from the mixer. This left the stand assembly. The raising lift arm had to be removed by unscrewing the set screw, and then the lift arm was removed. I replaced the plastic arm bowl lift by sliding it over the lift arm, and then I had to remove the spring with a clip washer with the pliers, and replaced the spring back on to the new part. Total time about ten minutes for the actual fix, and about 45 minutes remove and reinstall the 12 screws that held the motor in place. It was well worth my efforts. The mixer arm works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Nashville, TN
- Parts Used:
- WPW10731415
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One Wire Broke
All we had to do was place the new wire whip on and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from ENDWELL, NY
- Parts Used:
- WP9708649
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
all four feet on mixer damaged
I first ahd to remove the original feet by removing screws that held them in place. The new feet that I purchased were different then the original. They were a push in type and not held in by screws. I had to modify the base by drilling the foot holder to accept the new style feet. Once this was done, the feet were installed and looked good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from Gaithersburg, MD
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bent the original wire wisk
Just twisted it in to place. Parts Select was awesome! Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Cambridge, MA
- Parts Used:
- WPW10731415, W10803810
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a new whisk, the old one started to lose the wires
Just twisted it on just the same as you would changing attachments.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from SAINT LOUIS, MO
- Parts Used:
- WP9708649
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace rubber foot on mixer
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FLINT, MI
- Parts Used:
- W11200218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bad gears
Easily took apart and replaced gears. thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Iftikhar from PACIFICA, CA
- Parts Used:
- WPW10234531
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
dough mixer paddle not turning.
Connecting pin broken replaced. Tested unit works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LARGO, FL
- Parts Used:
- WP9706885
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
white plastic part on the lifter handle
Took off all the screws to open the mixer and install the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lane from Warrior, AL
- Parts Used:
- WP9707223
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
The mixer started getting weak like a gear was stripped and then quite working all together.
I removed the decorative band that covers the seam by removing 1 screw. I then removed the top portion of mixer by removing 4 square head screws. You will then see the gear housing in the front of the mixer. Remove the 4 screws holding that on. There are no spring that are going to pop out and you never know where they went, but be careful because there is a lot of grease and a gear that it just laying in there on the right side. You will see the stainless shaft with a couple on gear cogs on it. Remove the retaing spring from the shaft and pull the top gear off, it may be a little snug. You will then see the dowel pin, mine was sheared off but I could see where it was. Be sure to remove the broken pieces. Use the punch to knock out the remaining pin. Replace with new pin making sure it is evenly exposed on both side of the shaft. Replace the top gear, then the retaining spring, the the gear housing cover, then the mixer top cover and finally the decorative band. Be sure to unplug before you start. These mixers are expensive and expensive to have someone fix them. I ordered 2 pins because shipping is a little high and the pin is cheap. I fixed this for $17.00 total and have a spare pin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Orange Park, FL
- Parts Used:
- WP9708649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Mixer Feet startarted to disintergrate and leave marks on counter
Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David l from Heath, OH
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Install as per any accessory
Ordered part on Sunday, arrived on Tuesday morning. Mixer ready to use after washing and installing part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Statesboro, GA
- Parts Used:
- WPW10731415
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A broken part
I went to the web site and had a new part ordered within minutes and received it within a couple days! It could not have been easier!
Was this instruction helpful to you?
Thank you for voting!