Models
>
KP2671XWH3
KP2671XWH3 KitchenAid Mixer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$18.33
This is a genuine OEM worm following gear for your stand-up mixer. The gear is made of metal and is attached to the planetary shaft. This is an important part of the appliance as it helps to drive the...
In Stock
Order within the next 10 hrs and your part ships today!
$7.89
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is nois...
In Stock
Order within the next 10 hrs and your part ships today!
$22.13
This hub gear is a genuine OEM replacement part for your stand mixer. This kit includes both the beveled gear and attachment and is also referred to as a worm follower gear. This gear assists with the...
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
$60.19
NOTE: This part has been upgraded from plastic to metal housing. Gasket is no longer available separately.
***Used with Stand Mixers.
In Stock
Order within the next 10 hrs and your part ships today!
This assembly includes the black knob. Used with Stand Mixers.
In Stock
Order within the next 10 hrs and your part ships today!
$23.44
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
$65.17
This Stand Mixer Gear Grease lubricates the moving parts of the stand mixer.
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
In Stock
Order within the next 10 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KP2671XWH3
Viewing 3 of 3Noisy
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/11746909_1_S.jpg)
How to fix it
Touchpad does not respond
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/12070620_1_S.jpg)
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/11747009_1_S.jpg)
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/12348886_1_S.jpg)
How to fix it
Leaking
Fixed by these parts
![Fixing](https://fixcom-g4bhetdmcgd9b7er.z01.azurefd.net/assets/PartImages/11746938_1_S.jpg)
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barry from Rowland Heights, CA
- Parts Used:
- W11086780
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
wouldnt turn beaters
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease (
... Read more
do this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lake Mills, WI
- Parts Used:
- WPW10170081, WPW10170080, WP9709231, W11086780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Mixer Made Very Bad Grinding Noise, And Would Skip While Making Bread Dough
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them
... Read more
, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Read less
Was this instruction helpful to you?
Thank you for voting!
Plastic gear housing in stand mixer fractured causing gears to crash
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plasti
... Read more
c gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
Read less
Was this instruction helpful to you?
Thank you for voting!