Models
>
KHWG160PSS0
KHWG160PSS0 KitchenAid Miscellaneous
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for KHWG160PSS0
Viewing 3 of 3Manuals & Guides for KHWG160PSS0
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
In Stock
In Stock
$14.08
This is a genuine OEM replacement part. This screw is commonly used in the assembly of ranges, refrigerators, cooktops, air conditioners, wall ovens, dryers, microwave oven combos, microwaves, and was...
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for KHWG160PSS0
Viewing 1 of 1Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Woodstock, GA
- Parts Used:
- WP3193190
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
No Hot Water
I've replaced several Kitchen-Aid hot water dispensers because of no hot water. This time, I decided I'd dig deeper.
I noticed that the thermal fuse was the first item on the Part-Select list. I assumed it was the most frequently ordered part.
I removed the hot water tank from under the sink. I disassembled the tan ... Read more k and shell. I disassembled the tank and heating elelment. I tested the heating without the thermal fuse. I reassmbled the tank, replaced the thermal fuse, reassembled the tank and shell assemblly. Then I re-installed the entire heating unit back under the sink. Due to leaks, I had to redo the water supply connection. Then it worked fine! Note: I decided to replace the thermostat because the casing had become cracked and brittle. I ordered that seperately.
The exploded diagrams on the Part-Select site were extremely helpful in both diagnosing the problem and making the repair. Thanks for your help.
I noticed that the thermal fuse was the first item on the Part-Select list. I assumed it was the most frequently ordered part.
I removed the hot water tank from under the sink. I disassembled the tan ... Read more k and shell. I disassembled the tank and heating elelment. I tested the heating without the thermal fuse. I reassmbled the tank, replaced the thermal fuse, reassembled the tank and shell assemblly. Then I re-installed the entire heating unit back under the sink. Due to leaks, I had to redo the water supply connection. Then it worked fine! Note: I decided to replace the thermostat because the casing had become cracked and brittle. I ordered that seperately.
The exploded diagrams on the Part-Select site were extremely helpful in both diagnosing the problem and making the repair. Thanks for your help.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Aurora, OH
- Parts Used:
- WP3193190
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
No hot water
Unplug unit, turn off water, use 1/4" open end wrench to push down on collet holding in copper tubing - pull out copper tubing (per instructions in units manual), use pliers to squeeze clamp on water deliver plastic tube and remove. Bring unit up on counter, remove three screws holing top on and also remove on/off/temp knob and two screws
... Read more
holding nameplate trim ring on around knob. Locate thermal fuse wire (from thermostat to one leg of the heating element) and remove. Check continuity of both heating element and thermal fuse. No continuity in thermal fuse - replace -. Install new thermal fuse assembly by connection one end to the heating element and other end to thermostat. Re-assemble in reverse order of dissembly.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jake from Las Vegas, NV
- Parts Used:
- WP3193190
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
No instant hot water from unit
Removed unit (disconnected both top water tubes) because unit was behind garbage disposer. Unplugged and Drained water from unit. Then removed thermostat cover and top cover from unit to access the thermal fuse. Removed the thermal fuse by disconnecting the two electrical spade connectors. Replaced thermal fuse, reassembly and reinstalled
... Read more
unit. Problem fixed; unit is again producing instant hot water.
Read less
Was this instruction helpful to you?
Thank you for voting!