Models
>
MT4110SPB4
MT4110SPB4 Whirlpool Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MT4110SPB4
Viewing 6 of 6
Manuals & Guides for MT4110SPB4
Click to downloadInstall
Installation Instructions
(0.2MB)
Install
Installation Instructions
(0.25MB)
Manual
Owner's Manuals
(2.23MB)
Keep searches simple, eg. "belt" or "pump".
In Stock
$85.78
This kit contains 2 switches - 15 Amp - 125/250 Volt with 3/16" terminals.
In Stock
In Stock
This roller is located underneath the glass turntable. With the help of the motor, this roller helps to rotate the glass tray. This part takes the place of the coupling.
No Longer Available
In Stock
In Stock
In Stock
In Stock
$2.85
This screw is for microwaves.
A qualified technician should install this part if it requires accessing internal components of the microwave or microwave door. High-voltage capacitors can retain a l...
Special Order
This part guides the waves to the inside of the microwave to cook your food.
No Longer Available
$14.09
This is a genuine OEM replacement part. This screw is commonly used in the assembly of ranges, refrigerators, cooktops, air conditioners, wall ovens, dryers, microwave oven combos, microwaves, and was...
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for MT4110SPB4
Viewing 6 of 6Door stuck closed
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
No heat
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Doesn’t shut off
Fixed by these parts
How to fix it
Door not closing properly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sailendra from Round Rock, TX
- Parts Used:
- WP8205451
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
microwave door stuck....wont open
The reason the door would not open upon pressing the door opener is because the BRCKT-LATCH was broken. I discovered that after opening the microwave enclosing. The BRCKT-LATCH has two ends sticking out....each fits into a hole. One of the ends on the LATCH was broken and therefore it was not tightly fit. No upon pushing the door opener t
... Read more
he LATCH would not function properly since it was loosely fit and hence the door would not open.
To Fix this issue:
1) Buy a new BRCKT-LATCH
2) Remove the microwave enclosing. I had to use a special screwdriver, since the screws were security protected on my microwave. After removing the case, I opened the door by manually pressing the door latch upwards (please make sure that the microwave is not connected to the electric socket before removing the enclosing).
3) pull out the old LATCH from the microwave.
4) carefully insert the new LATCH. Try not to put too much pressure when trying to fit the latch, or else the ends may snap again!!
5) Close the door and try opening it by pressing the door opener. it should work now!!
To Fix this issue:
1) Buy a new BRCKT-LATCH
2) Remove the microwave enclosing. I had to use a special screwdriver, since the screws were security protected on my microwave. After removing the case, I opened the door by manually pressing the door latch upwards (please make sure that the microwave is not connected to the electric socket before removing the enclosing).
3) pull out the old LATCH from the microwave.
4) carefully insert the new LATCH. Try not to put too much pressure when trying to fit the latch, or else the ends may snap again!!
5) Close the door and try opening it by pressing the door opener. it should work now!!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bainbridge Island, WA
- Parts Used:
- 4392027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave worked intermittently depending on how door was closed
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and a
... Read more
lso took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from coto de caza, CA
- Parts Used:
- W10859575
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud buzzing noise
The repair went well...I am so glad that I read this info before buying a new microwave....it saved me lots of money. I did have a repair man come and look at it and he told me to buy a new one but it cost alot of money when it wasn't necessary. I did the repair and I was very proud of myself.
Three men watched a woman fix this and ... Read more it was no problem...they were impressed also....
Three men watched a woman fix this and ... Read more it was no problem...they were impressed also....
Read less
Was this instruction helpful to you?
Thank you for voting!