YKMHP519ES3 Whirlpool Microwave - Instructions

Unless you have a very comfortable background with electronics and electricity, I don't necessarily recommend taking apart a microwave. If you are very handy and are going to be VERY cautious to follow the rules of discharging caps and testing voltages before moving forward, then go for it. That said, I took the microwave off and apart. Not knowing where to find the parts, I was fortunate that the installer put the instruction book for the microwave inside the front vent slot above the touchpad for reference. it details the location of every part and it tells you very clearly what each part you test should show specific to this microwave on your multimeter. Find this guide online if you don't have it. Turn on the microwave for 20 seconds with a glass of water to make sure it's not heating - that with the noise means it's eeither the magnetron, cap, or diode. Read the notes on this site for all of the basic things to look for with the magnetron, diode, and capacitor. Once comfortable with the guide, locations of those devices, and how to test, then take it down and apart. Unfortunately, I didn't do all those things in that order, and it only wasted a lot of time trying to find the parts. Once I found the parts and put all the screws and covers back for all the areas that didn't need to be accessed for the repair, testing went quickly. The diode was bad. Ordered a new one and had it in 3 days or so. That means your microwave will be apart and sitting somewhere for a little while until you get the part and have time to repair it. Putting the diode back isn't too bad. Reassemble the microwave and put it back up again. If i had to do it again, it would take me 20 to 30 minutes once the microwave was down and on a table. Also, I used some bricks with towels over them or you could use some sawhorses to keep the microwave elevated so you can plug it in and run it after installing the new component. Again, make sure you discharge the cap before touching anything again even if you didn't run it, but just plugged it in.

I turn off the income electricity by shutting down the corresponding circuit breaker. Then, I removed the control panel from the microwave which gave me access to the capacitor and adjacent diode. After that i unscrewed the defective diode and replaced it with the new one and BINGO!

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

Remove two screws from Vent Grille, one on either side, and remove one screw inside Vent Grille on right side. Pull Vent Grille off exposing the two Charcoal filters. Remove the two Charcoal filters by hand and replace with new ones. Reinstall the Vent Grille and tighten screws. That's it. I'm not handy (ask my wife) and if I can do it so can you.

Whirlpool Microwave was purchased as used item, so installation in a new location required purchase of mounting template, wall bracket, mounting hardware. Granite backsplash cut out using wet/dry diamond blade and Ryobi 6.5 inch saw. Microwave exhaust fan removed and rotated for upward exhaust using modified exhaust plenum from existing stove exhaust hood. Installation of Microwave was the simplest part of the job. All mounting materials worked as required. A list of the materials provided in the hardware mount kit would be helpful, I would not have had to order the top mount screws separately if it was clear that they were included in the kit. Otherwise, no complaints.

Instead of telling you, i have question do you have any instructions on how to do the repair. It would have helped save time on the repair.

This job took longer then it should have, becasue I did not start right in the begining. I did figure it out quickly after the wrong start.

You were a big help in picking the right part to correct the problem. You should be able to help with the repair. Thank You

Followed instruction already on your website

I unscrewed the bottom plate of microwave oven and took a picture of how the wiring was plugged in and unscrew the motor and put the new one in,it was so easy to do

RATHER EASY. PHILIPS SCREWDRIVER, TORX DRIVER (FOR THE 2 SCREWS SECURING THE GEARMOTOR ITSELF), VERY SMALL SCREWDRIVER TO ASSIST IN DEPRESSING THE DETENTS ON ELECTRICAL CONNECTORS AT THE MOTOR. IF THE MICROWAVE IS ABOVE A STOVE UNIT, IT'S A GOOD IDEA TO PLACE A TOWEL DOWN ON THE STOVETOP TO CATCH ANY WAYWARD SCREW IF ONE HAPPENS TO GET AWAY. (VOICE OF EXPERIENCE)

Put New tray in convection microwave,closed door and it was done.

Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.

Remove top grill screws [2] remove grill replace filter put back together.

I measured. I leveled. I mounted hanging bracket and here's where it got tricky because you need two people to raise the microwave into position. I'd stack 2x4's In the back by the wall. I'd stackem in the front on the cabinet top then raise the back and add more. You get it front back front back until it's high enough to snag the bracket. Holes pre drilled raise it on up tighten bolts and poof you're done!! I did loosen the screws that pull the cabinets together and the bottom screw that holes the cabinet on one side. It didn't seem like it needed it the way it slipped in but maybe it slipped in because I did it. Only takes a minute. Use a minute here save an hour there. Go do it! Times a wastin!!

Removed the microwave from above the oven by loosening the two screws above the microwave. As the unit tilted outward lifted up and the whole unit came out all the time feeding the power cord through the cutout for the power cord. After it was out removed the cover and identified the capacitor and made sure it was discharged and removed and replaced the diode. tested before reinstalling and it heated up just fine. Reversed order and reinstalled . Very easy job maybe a second hand to help fish the power cord when installing and removing.

I used the microwave model number to order a replacement turntable. We received the item and it did not fit. Not even close. I will have to send it back. Very disappointed