MC7698W Samsung Microwave - Instructions

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Got the part and replaced it. Simple. Pleasure to work with

Ordered (most difficult part of repair, because I wasn't sure the one I ordered would fit), opened box, removed padding, opened microwave oven door, lined up center indentations with center and my repair was complete. Placed a cup of lukewarm coffee on the tray, closed door and pushed auto 30 seconds. The cup went round and round on the plate that went round and round and then, the END chime sounded. Success! Lukewarm coffee has been transformed to HOT coffee on the newly installed cooking tray.

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

I ordered a replacement piece. Fits perfectly and rotates as it should. It arrived earlier than planned.

Turn off power to microwave (kitchen circuit breaker) Remove 3 sheet metal screws bottom front, disconnect electrical connections to motor and lights, remove defective motor(1 screw), replace with new unit, replace screw, re-attach bottom (3) screws, test. Replacement motor cost via this supplier was 1/3 of what local appliance repair store would have charged.

My repair went terrible as I was sent the wrong motor 2 times. My stove sat in the middle of my small kitchen for 2 weeks. Finally the 3rd was the correct one except I didn't have the right nut so I waited another day for that to be sent. Everything working good now, I just hope the bottom fan doesn't go out after this experience.

My daughter was trying to run the microwave timer and ended up nuking the cooking tray, which shattered. First web place I found wanted 55$ for this tray and this site sold it for 19.99. It shipped super quickly. I am very pleased with this company!

Pretty easy tear down and assembly once I removed it from cabinet (built in micro)