Models
>
MMV5207BCB18
MMV5207BCB18 Maytag Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for MMV5207BCB18
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$24.24
The grease filter in your microwave range hood is used to trap dirt and debris from the air that result while cooking. A clogged and dirty filter can decrease the efficiency of your microwave, can cau...
In Stock
In Stock
In Stock
On Order
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
In Stock
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for MMV5207BCB18
Viewing 4 of 4No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Exhaust fan not working
Fixed by these parts
How to fix it
Door not closing properly
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from Bishop, CA
- Parts Used:
- WPW10187840
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broken handle
Remove the door by lifting up the hinge side so that the two hinge pins disengage from the steel hinge brackets.This can be a bit fiddly so just keep wiggling the door until one of them pops off.
Remove the plastic cover trim piece that surrrounds the window, exposing the phillips head screws that secure the door to the handle.
... Read more Remove the screws to un-install the old handle, they are deep set so if they fall out of the door you will need needle nose pliers to pout them back into the door.
Set teh new handle in place and tighten the screws down snuggly.
Retrace your steps... snap the plastic trim back in place and reset teh door on it's hinges (once again this can be a bit fiddly so take your time.
Eat a Burrito!
Remove the plastic cover trim piece that surrrounds the window, exposing the phillips head screws that secure the door to the handle.
... Read more Remove the screws to un-install the old handle, they are deep set so if they fall out of the door you will need needle nose pliers to pout them back into the door.
Set teh new handle in place and tighten the screws down snuggly.
Retrace your steps... snap the plastic trim back in place and reset teh door on it's hinges (once again this can be a bit fiddly so take your time.
Eat a Burrito!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Salt Lake City, UT
- Parts Used:
- 6802A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filters were missing from the over-the-stove microwave
Why a tenant would remove and discard the grease filters without replacing them is beyond me! But, I removed the filters from the package and slid them into place. Two minutes tops. I would like to add that I ordered these on Thursday afternoon, and I had them on Saturday; awesome customer service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Orlando, FL
- Parts Used:
- 4713-001165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not the original type bulb
The repair was very easy, however the bulb was not the same as the original one. The original bulb had a bright setting and a low setting, but the replacement bulb was only the low setting bulb. There was no bright and dim operation. The switch on the microwave had the duel settings.
Was this instruction helpful to you?
Thank you for voting!