MMV1153BAW Maytag Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judith from Fowler, OH
- Parts Used:
- DE74-20015B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My glass turntable had broke in my microwave.
Only had to set the new turntable in place. I was very impressed by the quickness in receiving the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN C from NORTH BEACH, MD
- Parts Used:
- R0713676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Both bulbs burned out at same time
I r/r the bulb cover, I then removed the burned out bulbs w/ a rag in case they broke they wouldn't have cut my fingers. You turn the bulbs lefty loosy. Installation is just the reverse. Install each bulb and turn righty titey, just snug the bulbs into place. Replace Glass cover and insert one phillips screw in plate and re-tighten
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Santa Cruz, CA
- Parts Used:
- DE67-00180A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The microwave turntable stopped rotating.
I ordered a new coupler and dropped it into the center hole, jiggled it until it fell into place, put the turntable back on the track, and voila, fixed! It was ridiculously easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Hudson, NH
- Parts Used:
- DE91-70063D
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Buzzing noise, no heating of food
Removed control panel, discharged HV capacitor. Removed old diode, tested to confirm failure. Replaced part. Other than the removal of the panel swapping the part was almost as easy as replacing a light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from CAMBRIDGE, MA
- Parts Used:
- DE91-70063D
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
Appears to work, but food not heated
The high voltage tired was shorted. I replaced it with a new one, but that did not solve the problem.
You can test the high voltage tired with a voltmeter and a 9 V battery. Search Search for it on YouTube.
You can also test the high voltage capacitor, the high-voltage transformer, and the magnetron with a multi meter. Search for the procedures on YouTube.
I tested all these high-voltage components with a low-voltage multi meter, and they all checked out OK (after replacing the diode). However the microwave still did not heat food.
When working on a microwave it is important to unplug it and also discharge the high voltage capacitor. The capacitor has a 10 megaohm resister to automatically discharge itself, but it may have failed – – so discharge it manually.
In the end I ordered a new microwave.
You can test the high voltage tired with a voltmeter and a 9 V battery. Search Search for it on YouTube.
You can also test the high voltage capacitor, the high-voltage transformer, and the magnetron with a multi meter. Search for the procedures on YouTube.
I tested all these high-voltage components with a low-voltage multi meter, and they all checked out OK (after replacing the diode). However the microwave still did not heat food.
When working on a microwave it is important to unplug it and also discharge the high voltage capacitor. The capacitor has a 10 megaohm resister to automatically discharge itself, but it may have failed – – so discharge it manually.
In the end I ordered a new microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from AKRON, OH
- Parts Used:
- DE67-40063A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass covering cook top lamp was broken
By removing one phillips headed screw, a metal frame pivoted down for easy replacement of glass plate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIFFINI from BUFFALO, WY
- Parts Used:
- WP3405-001034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would continue to run even when door was open. (even if no time was left on timer)
Unplugged Microwave, Removed vent cover (2 screws on top of microwave, then slide cover to the left, then forward) Removed control panel (1 screw at top of panel) then removed the two screws that hold in the door switch assembly. (these you will only see by opening the microwave). Located lower door switch, removed connecting wires, and pulled switch by releasing small plastic tab which held it in. Put new switch in place, reconnected wires, then reconnected door switch assembly. Reconnected control panel, and then put the vent cover back on. Tested microwave and it no longer runs when the door is open. Super easy fix, and was done in under 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from GOSHEN, IN
- Parts Used:
- DE96-00414A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave would keep running when door was open
Searched for a YouTube video that included “replace Samsung microwave body latch” (whatever part name). There are plenty of easy how-tos.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from GLEN BURNIE, MD
- Parts Used:
- DE96-00414A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
WHEN I CLOSED DOOR IT WOULD HUMM
REPLACED DOOR SWITCH ASSEMLY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenny from Blytheville, AR
- Parts Used:
- DE63-00196A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
filter on microwave
easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- louis from PARRISH, FL
- Parts Used:
- DE91-70063D
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Microwave stopped working - would not heat up
I removed the outer cover and exposed the inner workings. I watched a video on partselect.com to show how to remove and replace the Diode. I followed the instructions and it was very easy to replace.
Unfortunately, the diode was only part of the issue. I ended up replacing the High Voltage capacitor and Magnetron also. Those were a little more complicated but still easy to do.
Now the Microwave works just like new! Cost me less than $100 for all parts.
Unfortunately, the diode was only part of the issue. I ended up replacing the High Voltage capacitor and Magnetron also. Those were a little more complicated but still easy to do.
Now the Microwave works just like new! Cost me less than $100 for all parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from LONG BEACH, CA
- Parts Used:
- DE63-00196A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
VERY dirty- grease soaked- filters from under the above the stove microwave.
Pulled the filters down, measured and went on line- done. was fast to find the part and easy to order...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AMANDA from ANKENY, IA
- Parts Used:
- DE92-90505G
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
I picked up a used microwave that came with the needed mounting plate but no screws
Based on my research, this over the range miscrowave should have come with 2 templates: 1 for the wall and 1 for the underside of the wall cabinet. The challenge was to measure every very aspect of that microwave in order to obtain placement specs for the mounting screws. Tip: I made the holes through the top cabinet bottom a little larger than needed and used big washers with then for stability to gain the most "play" in the self aligning screws. Worked out well. Took 2 tries to get the wall plate perfect so have precision in mounting that piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Chicago, IL
- Parts Used:
- R0713676
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didn't work.
I opened the section with a phillips screwdriver, unscrewed the bad bulb and replaced it with the good bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Paso Robles, CA
- Parts Used:
- WPW10126786
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
microwave acts like its working but won't heat.
Replaced the magnetron and diode. Microwave works prefect now.
Was this instruction helpful to you?
Thank you for voting!