MS1240CB Maytag Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Judith from Fowler, OH
- Parts Used:
- DE74-20015B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My glass turntable had broke in my microwave.
Only had to set the new turntable in place. I was very impressed by the quickness in receiving the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tad from tamarack, MN
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave oven blew fuse
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denice from Montgomery, AL
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
microve stopped working
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Cottonwood, AZ
- Parts Used:
- WP8183592
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out.
Found instruction on internet,
1. Remove anit-tampering screws with punch and hammer
2. Remove the rest of the screws
3. Removed cover
4. Remove burned out bulb and installed new one
5. INstalled cover
6. Installed screws including the anti tampering onces
7. Op tested unit.
Wife is happy.
1. Remove anit-tampering screws with punch and hammer
2. Remove the rest of the screws
3. Removed cover
4. Remove burned out bulb and installed new one
5. INstalled cover
6. Installed screws including the anti tampering onces
7. Op tested unit.
Wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- connie from madison, NC
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Died while heating lasagna
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from W LAFAYETTE, IN
- Parts Used:
- WP8183592
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replacing light bulb in microwave
We have a Jenn-Air microwave and oven combination that is installed as a "stack" in a cabinet. The light bulb had burned out, and I read some of the posts on the partselect.com site about how others performed this replacement; ours was a bit different.
To replace the microwave light bulb, we had to remove the entire microwave and oven stack from the cabinet. There were four anchor screws on the sides (two on each side) of the microwave that were driven in perpendicular to the face of the microwave. There were four more screws that were on the sides of the oven that could be accessed once the oven door was open.
With those anchor screws removed, we had to carefully pull the entire microwave / oven stack from the cabinet to reach the top cover of the microwave. We used an old wooden crate to hold the front of the oven and left the back of the oven resting in the cabinet enclosure. This gave enough room to access the screws on the top cover of the microwave, without having to lift the entire stack down to the floor.
At this point, I could unplug the microwave power cord, which was plugged in to a socket built into the top of the conventional oven part of the stack.
The top cover of the microwave was attached with regular Phillips head screws, so those were easy to remove. Several other instructions indicated I would need a torx or star drive screwdriver, but I did not.
Once the screws were removed from the top cover of the microwave, the cover can slide rearward to be removed. However, there are two metal strips that run vertically along the sides of the microwave and at the top of the microwave, these bends over at a right angle over the top of the microwave. The top cover has tabs that sticks up vertically from the cover, so that the bent strips prevents the cover tabs from passing as the cover is slid backwards. The vertical strips have several screws connecting it to the body of the microwave. On one of the vertical strips, I removed the two of these screws closest to the top of the microwave. Then, I gently pushed a wood chisel, because of the bevel angle, between the vertical metal strip and the microwave body. This moved the bent-over portion of the vertical strip far enough away from the microwave that the tab on the top cover cleared the strip, and I could then remove the top cover.
With the top cover removed, I could see the old light bulb. It is attached with a push-in electrical connection that was easily pulled off. One Phillips head screwdriver held the old bulb in place towards the rear of the microwave. Towards the front of the microwave, a small plastic post holds the front of the bulb. I removed the screw and pulled out the old bulb.
The new bulb fits easily into the same plastic post and screw connection. However, the new bulbs connector prongs are bent at a 90 degree angle to the original bulb. Instead of sticking straight out from the microwave, which was how the old bulb was configured, the new bulb prongs pointed to the right side of the microwave (as viewed from the front). Fortunately, the wiring harness in the microwave that connects to the light bulb had a zip tie that was loose enough to get enough slack for the push-in connector to reach the new bulb's prongs.
After the bulb was in, I reversed the steps described above, making sure to leave the chisel in place until the top cover had been secured back in place. Once the chisel was removed from the vertical metal strip, the bent portion again would prevent easy removal of the top cover. I made sure to plug the microwave power cord back into the outlet on the conventional oven, then we slid the entire unit back into the cabinet enclosure, and I put the anchor screws back to hold the stack into the cabinet.
Three of us worked on this - mostly to help pull the stack out of the cabinet and to help steady it while the front was resting on the wood crate. This is not a single-person job. It was not terribly difficult, but the number of steps is very tedious. I found a helpful YouTube video "How to uninstall/install a Jenn-Air JMC8127DD/JMC8130DD Microwave Oven" posted by Ali The Handy Man. Being able to see that the microwave and oven stack was connected by a "bridge" (as Ali calls it) was a major help in tackling this.
After this, we suspect that Jenn-Air must have not wanted any repairs to their appliances. As I said above, this repair to replace a light bulb seemed unnecessarily tedious.
To replace the microwave light bulb, we had to remove the entire microwave and oven stack from the cabinet. There were four anchor screws on the sides (two on each side) of the microwave that were driven in perpendicular to the face of the microwave. There were four more screws that were on the sides of the oven that could be accessed once the oven door was open.
With those anchor screws removed, we had to carefully pull the entire microwave / oven stack from the cabinet to reach the top cover of the microwave. We used an old wooden crate to hold the front of the oven and left the back of the oven resting in the cabinet enclosure. This gave enough room to access the screws on the top cover of the microwave, without having to lift the entire stack down to the floor.
At this point, I could unplug the microwave power cord, which was plugged in to a socket built into the top of the conventional oven part of the stack.
The top cover of the microwave was attached with regular Phillips head screws, so those were easy to remove. Several other instructions indicated I would need a torx or star drive screwdriver, but I did not.
Once the screws were removed from the top cover of the microwave, the cover can slide rearward to be removed. However, there are two metal strips that run vertically along the sides of the microwave and at the top of the microwave, these bends over at a right angle over the top of the microwave. The top cover has tabs that sticks up vertically from the cover, so that the bent strips prevents the cover tabs from passing as the cover is slid backwards. The vertical strips have several screws connecting it to the body of the microwave. On one of the vertical strips, I removed the two of these screws closest to the top of the microwave. Then, I gently pushed a wood chisel, because of the bevel angle, between the vertical metal strip and the microwave body. This moved the bent-over portion of the vertical strip far enough away from the microwave that the tab on the top cover cleared the strip, and I could then remove the top cover.
With the top cover removed, I could see the old light bulb. It is attached with a push-in electrical connection that was easily pulled off. One Phillips head screwdriver held the old bulb in place towards the rear of the microwave. Towards the front of the microwave, a small plastic post holds the front of the bulb. I removed the screw and pulled out the old bulb.
The new bulb fits easily into the same plastic post and screw connection. However, the new bulbs connector prongs are bent at a 90 degree angle to the original bulb. Instead of sticking straight out from the microwave, which was how the old bulb was configured, the new bulb prongs pointed to the right side of the microwave (as viewed from the front). Fortunately, the wiring harness in the microwave that connects to the light bulb had a zip tie that was loose enough to get enough slack for the push-in connector to reach the new bulb's prongs.
After the bulb was in, I reversed the steps described above, making sure to leave the chisel in place until the top cover had been secured back in place. Once the chisel was removed from the vertical metal strip, the bent portion again would prevent easy removal of the top cover. I made sure to plug the microwave power cord back into the outlet on the conventional oven, then we slid the entire unit back into the cabinet enclosure, and I put the anchor screws back to hold the stack into the cabinet.
Three of us worked on this - mostly to help pull the stack out of the cabinet and to help steady it while the front was resting on the wood crate. This is not a single-person job. It was not terribly difficult, but the number of steps is very tedious. I found a helpful YouTube video "How to uninstall/install a Jenn-Air JMC8127DD/JMC8130DD Microwave Oven" posted by Ali The Handy Man. Being able to see that the microwave and oven stack was connected by a "bridge" (as Ali calls it) was a major help in tackling this.
After this, we suspect that Jenn-Air must have not wanted any repairs to their appliances. As I said above, this repair to replace a light bulb seemed unnecessarily tedious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from STRUM, WI
- Parts Used:
- WPM0805101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave went pop and nothing would work.
I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- leverett from villa ridge, MO
- Parts Used:
- WP8183592
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
interior lamp burnt out
remove outer cover of microwave, (special recessed star bit required) change bulb, unplug and remove 1 phillips screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIFFINI from BUFFALO, WY
- Parts Used:
- WP3405-001034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave would continue to run even when door was open. (even if no time was left on timer)
Unplugged Microwave, Removed vent cover (2 screws on top of microwave, then slide cover to the left, then forward) Removed control panel (1 screw at top of panel) then removed the two screws that hold in the door switch assembly. (these you will only see by opening the microwave). Located lower door switch, removed connecting wires, and pulled switch by releasing small plastic tab which held it in. Put new switch in place, reconnected wires, then reconnected door switch assembly. Reconnected control panel, and then put the vent cover back on. Tested microwave and it no longer runs when the door is open. Super easy fix, and was done in under 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from OKLAHOMA CITY, OK
- Parts Used:
- DE31-10154D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable Quit
Snipped four corners off inspection panel,removed one phillips screw and two elect. Connections. Reverse process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from MYRTLE BEACH, SC
- Parts Used:
- DE92-90189S
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Part broke
Got the part and replaced it. Simple. Pleasure to work with
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norbert from BROUSSARD, LA
- Parts Used:
- WP8183592
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave Oven Light Burned Out
There were two hard parts for me to work through.
The first was breaking off the two screws that need a special head screwdriver to remove. None of my special special head screwdrivers worked (I have a few), so I used a hammer to force them off.
The second hardest part for me was finding the correct replacement bulb on-line. My Amana Microwave is a combo Microwave/Convection type, and it's a strange little bulb - almost tube like.
Once I did find the right bulb on this PartSelect.com website it was a breeze. The part was delivered in just a couple of days (even during this Covid-19 pandemic). Once I had the replacement bulb in hand it barely took 5 minutes to install.
Thanks PartSelect!!
The first was breaking off the two screws that need a special head screwdriver to remove. None of my special special head screwdrivers worked (I have a few), so I used a hammer to force them off.
The second hardest part for me was finding the correct replacement bulb on-line. My Amana Microwave is a combo Microwave/Convection type, and it's a strange little bulb - almost tube like.
Once I did find the right bulb on this PartSelect.com website it was a breeze. The part was delivered in just a couple of days (even during this Covid-19 pandemic). Once I had the replacement bulb in hand it barely took 5 minutes to install.
Thanks PartSelect!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CALIFORNIA, KY
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No power to any microwave functions
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mason from SUTTON, MA
- Parts Used:
- WP8183592
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Light Bulb Out.
1. Order correct light bulb for unit and have it with you before removing old lightbulb.
My Microwave is built into cabinet.
2. Disconnect power (Either turn breaker off or unplug unit from wall)
3. Remove face cover on cabinet. (4 Phillips head screws)
I was able to reach in the opening in the cabinet and unplug from the wall.
4. Remove Phillip head screws holding microwave in cabinet.
5. Remove microwave from cabinet.
6. Remove Phillip head screws and torx screws holding outside cover on the back of unit and the side (1 on right side) and then remove cover.
Light bulb is on the top front right side.
7. Remove 1 philip head screw holding light bulb and unplug quick connector wires.
8. Plug quick connector into new light bulb same way it came out and place new light bulb in place and put the 1 philips head screw holding it back in place.
9. Put cover back on and all the screws. Temporary plug the unit in to test light bulb works before securing it back into cabinet.
10. Reverse order 5,4,Plug unit in wall before putting the face back on.
Done.
My Microwave is built into cabinet.
2. Disconnect power (Either turn breaker off or unplug unit from wall)
3. Remove face cover on cabinet. (4 Phillips head screws)
I was able to reach in the opening in the cabinet and unplug from the wall.
4. Remove Phillip head screws holding microwave in cabinet.
5. Remove microwave from cabinet.
6. Remove Phillip head screws and torx screws holding outside cover on the back of unit and the side (1 on right side) and then remove cover.
Light bulb is on the top front right side.
7. Remove 1 philip head screw holding light bulb and unplug quick connector wires.
8. Plug quick connector into new light bulb same way it came out and place new light bulb in place and put the 1 philips head screw holding it back in place.
9. Put cover back on and all the screws. Temporary plug the unit in to test light bulb works before securing it back into cabinet.
10. Reverse order 5,4,Plug unit in wall before putting the face back on.
Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Rockwall, TX
- Parts Used:
- WP8183592
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dead Light bulb
Required that i remove the built in frame and mounting. Required tamper proof socket to remove housing. I removed the old bulb and simply replaced and reverse installed the cabinet.
Was this instruction helpful to you?
Thank you for voting!