Models
>
CMV1000ADW
CMV1000ADW Maytag Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for CMV1000ADW
Viewing 6 of 6Keep searches simple, eg. "belt" or "pump".
$8.87
To access the exterior lightbulb, the bottom panel of the microwave will need to be removed. It is secured in place with screws, so will require a Philips screwdriver to remove it. Screw the new light...
In Stock
$20.79
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
In Stock
In Stock
$10.19
This is a ceramic fuse for a microwave. It is just over 1 inch long. This fuse is 20 amps and 250 volts. This part powers your microwave. If your appliance is not heating properly, or is not turning o...
In Stock
In Stock
This outer door handle is half of a two piece door handle assembly. It is all white in color and is made entirely of plastic.
In Stock
$19.63
This charcoal air and grease filter is a little over ten inches long. It has a metal perimeter, a metal mesh exterior, and a black charcoal interior.
In Stock
This turntable tray is eleven inches in diameter. It is made entirely of glass.
No Longer Available
This inner door handle is half of a two piece door handle assembly. It is all white in color and it is made entirely of plastic.
In Stock
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for CMV1000ADW
Viewing 2 of 2Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Deborah from Millersville, MD
- Parts Used:
- 8206232A
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light bult needed to be replaced
The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the li
... Read more
ght bulb so that we do not need a screwdriver to remove the door to get to the light bulb
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Pembroke, MA
- Parts Used:
- 8206232A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bulb "burnt out"
Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from PARADISE, PA
- Parts Used:
- WPR9800486
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
no heat
I looked up the #1 reason for no heat for my microwave on the site , and using my model number found that 92% of the time it was the Black Sleeve Diode. Ordered the $15 part, and installed it within 30 minutes. Most of the time was used for removing the built in microwave and removing the cover. Replaced the diode by finding it on the
... Read more
diagram that I printed from this site (free). Very relieved that we don't need to have our custom cabinetry re-sized to accommodate a new microwave. Thank you!
Read less
Was this instruction helpful to you?
Thank you for voting!