DM130LC Magic Chef Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- tad from tamarack, MN
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
microwave oven blew fuse
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denice from Montgomery, AL
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
microve stopped working
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- connie from madison, NC
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Died while heating lasagna
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from STRUM, WI
- Parts Used:
- WPM0805101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave went pop and nothing would work.
I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terri from Kingsland, TX
- Parts Used:
- WPA3167501
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Bulb
Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathtleen from Bristol, CT
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out lightbulb for over 20 years
Unscrewed back plate, and replaced bulb
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dolores from Scottsdale, AZ
- Parts Used:
- WP51001121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Turntable would not turn
Placed the new turnbable in the microwave and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CALIFORNIA, KY
- Parts Used:
- WPM0805101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No power to any microwave functions
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BURSON, CA
- Parts Used:
- WPA3167501
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light bulb went out in mictowave
Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deidre from Brownsville, TX
- Parts Used:
- WPA3167501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Microwave oven bulb had burned out
My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.
The whole operation took less than 5 mins.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Rochester, NY
- Parts Used:
- Y02450002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My microwave lost the nylon drive gear for the turntable
I just lifted off the turntable, cleaned spilled food from under it, slipped on the gear, and replaced the turntable.
PartSelect's superb website made finding the model number and the parts diagrams for that model super fast and easy. From there, ordering the part was a snap.
PartSelect's superb website made finding the model number and the parts diagrams for that model super fast and easy. From there, ordering the part was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Annapolis, MD
- Parts Used:
- WP51001121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Warped turntable tray
Removed old replaced with new......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Littleton, CO
- Parts Used:
- WP51001121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
table worps on regular basis - poor design material
lift out old tray and place in new tray.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Felton, DE
- Parts Used:
- WP51001121
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
turntable was warped and wouldn't turn
replaced old with new and everything was fine
Was this instruction helpful to you?
Thank you for voting!