Models > 5648878310

5648878310 Kenmore Microwave

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 5648878310

Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
This water inlet valve is intended for use with horizontal motor dishwashers. It uses a 3/8 of an inch valve tubing and a mounting bracket.
No Longer Available
$10.83
This clamp helps to prevent leaking by holding the end of water hose in place.
In Stock
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available
No Longer Available

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for 5648878310

Viewing 2 of 2
Will not fill with water
Fixed by these parts
Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Atlanta, GA
Parts Used:
3374621
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
Dishwasher running with no or little water.
Removed screws under counter holding washer in place. Pulled washer out until I could access the back. Turned water supply off (in my case faucet under the sink) Turned power off at breaker.
Disconnected water line and electrical wires noting wire location. Removed solenoid unit by undoing two screws on frame. Installed new unit, co nnected wires and water. Turned water on to ensure no leaks and pushed washer back under counter. Turned power back on and checked machine operation. Replaced the screws under the counter to keep machine in place. This is very easy. In my area a plumber would charge $75 to do this.
21 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from North Las Vegas, NV
Parts Used:
3374621
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
my wife said no water coming to dishwasher!
i took off the kick plate and found the water valve. its the piece that water comes to from under the sink to connect to the dishwaser. it has a plug with 2 wires. i turned off the water supply, disconnected the wires(probably should have flipped the breaker but didnt) took out the 5/16 mounting screws, had to use a little end wrench on 1 because it was behind the water line and a nut driver on the other. i put some thread gook on the connection and put the new one in the way it was and it works great. i am writing this because thats where i got the info to diagnose in the first place and saved me $$$!
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judy from Macomb, MI
Parts Used:
3374621
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dishwasher working with no water coming in
Turned off water and electrical. Removed kickplate at bottom of dishwasher. Unhooked water line, electrical plug and unscrewed valve from frame, noting proper position of valve for new install. The only delay we had was removing the old water line fitting from old valve. We needed the old fitting for the new valve. We solved the prob lem by soaking valve in boiling hot water to help loosen the connection. Install of new valve was reverse of the removal process. My son did the work and saved me approximately $200 for a service call. I also want to say that ordering the part from your company was less expensive than if I had ordered it locally and gone to pick it up! Your website is extremely helpful, user friendly, and I am recommending it to all my friends when they need to repair an appliance. Thank you!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!