36363673200 Kenmore Microwave - Instructions

Turned out the issue was easily solved by replacing a single, inexpensive fuse.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.

Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!

I have a GE Advantium/micorwave oven. It is the model that has the hinges on the side, NOT the bottom. First, removing the door is necessary. The grill has to be removed first, then the door lifts right out. Next the plastic backing on the door has to be very carfully taken off to expose where the new latch has to be placed. Use a flat screw driver or putty knife to go around the permiter releasing the internal, unseen, plastic catches that hold it on. This should be done carefully, to avoid breaking the catches that you can't see. After the plastic is mostly removed putting in the spring is not too difficult, but a second set of hands is almost manditory.

Easy as pie!
1. Remove the 2 outer screws holding the top vent in place and remove the vent (it helps to have the door open)
2. Lift the door up, pull the top of the door away from the hinge and then list it up a little more to clear the bottom hinge.
3. Lay the door on the counter and with a putty knife, work your way around the perimeter of the door between the door and the inside bezel. The bezel is held in place with little tabs spaced evenly around the perimeter.
4. Once the bezel is off, the catch assembly is accessible. List it up against the spring pressure, and push it towards the outside of the door to release it from the frame.
5. Reverse procedure to install.

It was super easy! Opened the door, matched up the hole on the side of the microwave convection oven with the first portion of the rack holder clip, pushed in the rack holder clip and made a twist to ensure the rack holder clip seated in the wall of the oven. Less than 30 seconds to install - no tools necessary. I that the clips came in an order of a unit of 8 clips, allowing me a quick-fix if I need additional clips for loss. Now I have stable racks within my oven ensuring safe insertion and removal of food from the oven. Having the full use of both of the racks in my convection oven during the summer is a Godsend, especially living in the Ohio Valley with its' hot steamy summers - my kitchen stays cool as a cucumber, and so do I!

The old fuse is perfectly good. The new ones arrived within a day.

Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover
and test to see if that solved the problem. If so then well done!!

First I disconnected the power and opened the door. Then I removed the top screws holding the top vent louvers, then removed the screw at the top of the touch pad. The touch pad removes by sliding up slightly then tilting top out. I unscrewed two screws holding the door latch assembly. Press the tab to remove and replace switch. Reconnect wires, reseat latch mount by placing top bracket tab in place first, allign and secure with screws. Reseat touch pad by placing bottom tabs in first, tilt forward and press up to seat top tabs, secure with top screw. Secure vent louver screws, plug in and watch your microwave work again.

I broke the tray glass in the microwave cleaning it so this was a no brainer. The best part of this was the PartSelect experience. I ordered the part on the 30th of December and received it on 3 Jan!!! I have used PartSelect before for fridge repair and had the same experience.

1. turned off electricity -- unplugged the unit 2. removed 3 screws on top of top vent, removed vent screen then I located the little white cylindrical fuse and popped it out with a table knife. Then I popped in the new fuse. Replaced the vent screen and screws -- plugged in the appliance and it is working again.

This is the second time that this lamp hase gone out. It is located in a small space in the top of the microwave and you need to remove the top front pannel, then take a screw or two out of a metal shield and bend the shield up to get your hand into the compartment where, if you know how, you can reach in and lift out the reflector shield that the lighbulb is plugged into and remove the old one and plug in the new one. The first time was hard to figure out how to do it but the second time wasn't bad because I knew how to do it.

*Remove Two Phillips head screws from the top of vent slide the vent left to remove it. Take the charcoal filter out then the metal cover underneath the filter. It also has a phillips head screw. bulb socket is on right facing down. Squeeze the metal clips and remove socket from bracket. Installation is the reverse of removal.

No actual repair was necessary. However I do want to thank PartSelect for sending a replacement so quickly.

the door lifts off two pins after you remove the top piece. I broke the choke cover prying it off. It has little plastic things that hold the cover on. I popped it off from the outside. I think you may not break the clips if you go from the inside on the top an bottom. There are 3 on the top and 3 on the bottom about 4 inches in and in the center. The sides come off real easy. Even breaking the choke cover it was still almost $200 cheaper than the repair man.

After removing the screws holding the 2 cover plates in position, I removed the halogen light bulbs with my fingers. Then I placed a paper towel around the first replacement bulb and lined up the two wire connectors with the two holes in the receptacle. I pushed in, but the bulb's probes did not slide into the receptacle. I spent five minutes aligning and pushing but to no avail. Then I removed the filter screen on the side of the receptacle, shined a flashlight beam on the receptacle, and with an improved view of the two holes in the receptacle, slid the bulb in. The second bulb was inserted in a few minutes, and the job was done. Whoever designed the halogen bulb was not as bright as Thomas Edison.