Models > JMV8208WS0

JMV8208WS0 Jenn-Air Microwave

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for JMV8208WS0

Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
To access the exterior lightbulb, the bottom panel of the microwave will need to be removed. It is secured in place with screws, so will require a Philips screwdriver to remove it. Screw the new light...
In Stock
This is a charcoal filter for an over-the-range microwave. It is designed to absorb grease before making its way into the vent, which could cause damage or build-up. It also helps to reduce odors whil...
In Stock
This is a single grease filter for a microwave. Most microwaves have two filters, the other one being the charcoal filter, which is a different filter, sold separately, and has different maintenance i...
In Stock
This is the replacement lightbulb for your over-the-range microwave. It is found on the underside of your microwave and is used to illuminate your stovetop while you are cooking. This is a genuine OEM...
In Stock
This mounting plate is a genuine OEM part for your microwave. This metal bracket is approximately 30 inches in length and is used to support your microwave when installed under cabinets. Please note t...
In Stock
This is an authentic OEM door switch for your microwave. This switch is located behind the front panel, and works by making contact with the door hook, sending a signal that the door is closed and the...
In Stock
This screw is sold individually.
In Stock
The microwave door interlock switch prevents the microwave from starting if the door is open. If your microwave will not start when the door is closed, or it continues running if the door is opened, t...
In Stock
This part protects the microwave by shutting it off if there is an electrical surge.
In Stock
$29.50
This part allows power to go one way but not the other.
In Stock
$60.95
This assembly includes the damper door and frame.
In Stock
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for JMV8208WS0

Viewing 7 of 7
Won’t turn on
Fixed by these parts
Fixing Fixing
How to fix it
No heat
Fixed by these parts
Fixing Fixing
How to fix it
Door not closing properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Exhaust fan not working
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Tray won’t turn
Fixed by these parts
Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Doesn’t shut off
Fixed by these parts
Fixing Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Deborah from Millersville, MD
Parts Used:
8206232A
Difficulty Level:
Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
light bult needed to be replaced
The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the li ght bulb so that we do not need a screwdriver to remove the door to get to the light bulb
207 of 303 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from HOMER GLEN, IL
Parts Used:
WPW10156813, WP8206419, W10727360, W10562613, W10269460, W10269458, W10156812
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Door switch inconsistent operation for Open/Close sensing.
Ordered top & bottom micro-switches and mounting plate parts. Internet reviews could not find specifics if the issue was due to a top/bottom or combination of micro-switch or mounting plate failure. Pulled the plug. Removed the top vent assembly cover held in by 2 Phillips screws inside the vent. Removed the control panel held in by 1 P hillip screw at the top vent assembly area. Lifted control panel upward to release the catch and moved it off to the side - didn't disconnect any leads. Used a Torx bit to remove the door switch mounting plates at the front and pulled the plates through the opening from the control panel. Documented the wire color code connections, the top plate uses 2 micro's with one using both the closed & open contact. Installed the respective micros on the mounting plates and worked backwards with the wiring and removal steps. Once completed, the open/close sensing has worked every time.
118 of 141 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Pembroke, MA
Parts Used:
8206232A
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bulb "burnt out"
Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.
93 of 146 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!