Models
>
JMC2127WB00
JMC2127WB00 Jenn-Air Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JMC2127WB00
Viewing 6 of 6Keep searches simple, eg. "belt" or "pump".
$5.42
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 12 hrs and your part ships today!
$44.72
This door switch (Primary and Secondary) keeps the microwave from running when the door is open.
NOTE: Two switches required. Sold individually.
In Stock
Order within the next 12 hrs and your part ships today!
$17.79
This part is the replacement halogen light bulb for your range. The bulb is 10 watts and 12 volts. The halogen lamp lights up the inside of the oven you can see the cooktop more effectively in darknes...
In Stock
Order within the next 12 hrs and your part ships today!
$62.03
This roller is located underneath the glass turntable. With the help of the motor, this roller helps to rotate the glass tray. This part takes the place of the coupling.
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
On Order
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
$293.16
The inverter acts like the brain for the microwave. It sends high voltage to the magnetron to produce heat.
On Order
In Stock
Order within the next 12 hrs and your part ships today!
In Stock
Order within the next 12 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JMC2127WB00
Viewing 4 of 4Tray won’t turn
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
No heat
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- E G from SILVERDALE, WA
- Parts Used:
- W10211972
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The display kept asking me to close the door, even though the door was closed. The interior light stayed on.
I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed
... Read more
in transit so your agent credited me with the cost of shipping.
When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.
All seems to be working well now.
Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?
When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.
All seems to be working well now.
Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from SOLVANG, CA
- Parts Used:
- W10886919
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burnt out Microwave Lamp
IMPORTANT: DO NOT TOUCH THE REPLACEMENT LAMP WITHOUT WEARING CLEAN GLOVES. FILM OR FINGER PRINTS ON THE LAMP GLASS WILL CAUSE PREMATURE FAILURE OF THE LAMP.
Remove the 4 screws on right and left mounting rails that hold the unit to the kitchen cabinet.
Remove the oven door
Remove the chrome oven vent strip below the ... Read more oven door. This allows a pry point beneath the combo microwave oven assembly to lift up the unit while pulling it out. (Assembly weighs 250 pounds)
Pull the unit out from the cabinet housing about 2-3 inches to reveal the right and left sides and the 4 screws holding the the control panel.
Remove the 4 control panel screws and pull off the face of the control panel
Remove the 2 harness connectors and the ground wire holding the control panel to the unit.
Unclip the circuit board above the lamp connector and slide it back out of the way. The lamp is now accessible.
Remove the lamp spring holding the lamp to the cabinet.
Remove the old lamp
Install the new lamp using clean gloves
Reassemble in reverse order.
Remove the 4 screws on right and left mounting rails that hold the unit to the kitchen cabinet.
Remove the oven door
Remove the chrome oven vent strip below the ... Read more oven door. This allows a pry point beneath the combo microwave oven assembly to lift up the unit while pulling it out. (Assembly weighs 250 pounds)
Pull the unit out from the cabinet housing about 2-3 inches to reveal the right and left sides and the 4 screws holding the the control panel.
Remove the 4 control panel screws and pull off the face of the control panel
Remove the 2 harness connectors and the ground wire holding the control panel to the unit.
Unclip the circuit board above the lamp connector and slide it back out of the way. The lamp is now accessible.
Remove the lamp spring holding the lamp to the cabinet.
Remove the old lamp
Install the new lamp using clean gloves
Reassemble in reverse order.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from BURLESON, TX
- Parts Used:
- W10886919
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Bulb entirely to small and unopened
Should be about 1 5/8 inch with 3/8 inch prongs. Sent bulb won’t fit.
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I r ... Read more eturn the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961
JennAire book showed
Part 74004458-halogen bulb part PS 11765655 was substituted.
I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven.
I need the correct part
where do I r ... Read more eturn the unopened $29.95 bulb for credit on my card and receive the correct one?????
Carolyn Sanders 817-319-6581
Order 21938961
Read less
Was this instruction helpful to you?
Thank you for voting!