Models
>
JMV8208ACS
JMV8208ACS Jenn-Air Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JMV8208ACS
Viewing 6 of 6Manuals & Guides for JMV8208ACS
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
$60.87
This part is the replacement halogen lamp for your range hood. The bulb is 35 watts and 130 volts. The halogen lamp lights up the area under the range hood so you can see the cooktop more effectively ...
In Stock
In Stock
$41.00
This is the replacement charcoal filter for your microwave. It is black in color and measures approximately 11 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air that circul...
In Stock
$85.78
This kit contains 2 switches - 15 Amp - 125/250 Volt with 3/16" terminals.
In Stock
$8.25
This rivet is used for the stirrer cover/wave guide. They are sold individually.
In Stock
In Stock
In Stock
This vent grille mounts on the top of the microwave above the door.
No Longer Available
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JMV8208ACS
Viewing 3 of 3No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Doesn’t shut off
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Guy from Bellingham, MA
- Parts Used:
- WP59001168, WPR9800486
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Sparks and loud hum from oven
1. I went to the internet to find the service manual for the Maytag microwave.
2. I opened up the oven and started measuring the resistance of the diode, capacitor, transformer, and magnetron between terminals and then to ground. The transformer and magnetron were well within the resistance limits. The diode was shorted in both direc ... Read more tions(+-). The capacitor was fully open in both directions -- high resistance.
3. I ordered the 2 parts, installed them, and ran the oven. Worked perfect first time.
4. Reinstalled oven and worked ever since (1 week so far).
5. The secret was that the transformer had a load hum. I figured the transformer was OK. The magnetron had no short between filaments and ground to filaments. The only two left were the diode and capacitor. The first two are about $200 -- almost the value of a new microwave. The $70 repair was well worth it. If the first two were still bad, then tempted to buy a new oven.
2. I opened up the oven and started measuring the resistance of the diode, capacitor, transformer, and magnetron between terminals and then to ground. The transformer and magnetron were well within the resistance limits. The diode was shorted in both direc ... Read more tions(+-). The capacitor was fully open in both directions -- high resistance.
3. I ordered the 2 parts, installed them, and ran the oven. Worked perfect first time.
4. Reinstalled oven and worked ever since (1 week so far).
5. The secret was that the transformer had a load hum. I figured the transformer was OK. The magnetron had no short between filaments and ground to filaments. The only two left were the diode and capacitor. The first two are about $200 -- almost the value of a new microwave. The $70 repair was well worth it. If the first two were still bad, then tempted to buy a new oven.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bainbridge Island, WA
- Parts Used:
- 4392027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Microwave worked intermittently depending on how door was closed
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and a
... Read more
lso took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from coto de caza, CA
- Parts Used:
- W10859575
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud buzzing noise
The repair went well...I am so glad that I read this info before buying a new microwave....it saved me lots of money. I did have a repair man come and look at it and he told me to buy a new one but it cost alot of money when it wasn't necessary. I did the repair and I was very proud of myself.
Three men watched a woman fix this and ... Read more it was no problem...they were impressed also....
Three men watched a woman fix this and ... Read more it was no problem...they were impressed also....
Read less
Was this instruction helpful to you?
Thank you for voting!