M439B1 Jenn-Air Microwave - Instructions

I pulled out the old filters and just put in the new ones with ease, it was that simple. No screws was needed.

The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the light bulb so that we do not need a screwdriver to remove the door to get to the light bulb

Removed 1 screw, removed "burnt out" bulb and replaced it with new bulb.

The metal screen in the door of my microwave was rusting and making my "window" look nasty. I was able to take apart the door w/o removing the microwave, peel off the old plastic seal and clean the nasty parts of the glass door. The rust still remains and may be a future problem. But for now, the cleaning was what the door needed and applying the new film was a simple as putting stickers on a gift bag.

FIrst I removed the glass bulb cover, old bulbs, and old filters. Then I removed the 6 screws that held the lower cover in place, and bulb sockets. Then washed all parts an reassembled with new bulbs and filters.

used screw driver to remove cover and replaced the filter

It was a piece of cake....slid filters down and out, replace with new filters, slid down filter openings slightly and pulled filter up in to place. Done in less than one minute.

removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

The hard part was trying to find the light bulb locally. The locally sold light bulbs were either too long, not dual element or not powerful enough. So I ordered the light bulb straight from PartSelect. When it came time to install the new light bulb I carefully removed the screw holding the plate in position so as not to loose it in my gas stove. I needed the mirror to line up the light bulb and screw it in. Once it was in I verified operation and closed up the plate being careful not to drop the screw into my gas stove. Problem solved.

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

I had previously removed the old grill vent and filter, so the hardest part of the re-installation was removing the new parts from the shipping box. Once out, the filter dropped in place, the new grill snapped into place and after tightening two screws the work was done. Kudos to Partselect for availability of these parts for a 15 year old appliance and for fast shipping (ordered Sunday, received Wednesday).

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.