Models
>
JVM8208ACB
JVM8208ACB Jenn-Air Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$35.15
Reduce cooking odors in a recirculating microwave ventilation system with this charcoal filter. Before exhaust air returns to the kitchen, activated carbon captures odors to help keep the room fresher...
In Stock
Order now and your part arrives by Nov 22
$26.22
Help the microwave detect whether its door is closed with this interlock switch. The latch operates a small actuator that changes the electrical contact as the door opens and shuts, supporting the saf...
In Stock
Order now and your part arrives by Nov 22
$21.95
Secure door closure relies on this black plastic microwave door latch hook. Installed inside the door assembly, it engages the latch openings and operates the safety interlock switches when the door c...
In Stock
Order now and your part arrives by Nov 22
$21.95
Exhaust air passes through this microwave vent damper when the ventilation fan runs. The metal flap opens with outgoing airflow to let steam and cooking odors enter the exhaust duct, then closes when ...
In Stock
Order now and your part arrives by Nov 22
$21.82
This 20 watt, 120 volt halogen lamp provides replacement illumination for the microwave cavity or cooktop light, depending on the appliance design. Bright appliance lighting makes food and cooking sur...
In Stock
Order now and your part arrives by Nov 22
In Stock
Order now and your part arrives by Nov 22
$11.98
Rated at 20 amps and 250 volts, this microwave time delay fuse protects against electrical overload. It accommodates the brief current surge at startup but opens the circuit during a sustained overloa...
In Stock
Order now and your part arrives by Nov 22
$26.22
This genuine OEM light socket provides power to the light bulb in your microwave while holding it in place. This light socket is two pronged and the bulb should screw easily into it. If your light bul...
In Stock
Order now and your part arrives by Nov 22
On Order
$134.28
Convert power from the microwave?s high-voltage circuit into the microwave energy used to cook and warm food with this magnetron. A failed unit may stop heating even though the fan, turntable, and dis...
In Stock
Order now and your part arrives by Nov 22
If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed thr...
In Stock
Order now and your part arrives by Nov 22
$17.44
Current flows in one direction through this microwave high voltage diode and cable assembly, which works with the capacitor and transformer to supply the magnetron. This electrical process supports th...
In Stock
Order now and your part arrives by Nov 22
Common Problems and Symptoms for JVM8208ACB
Viewing 6 of 6Door not closing properly
Fixed by these parts
How to fix it
No heat
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Tray won’t turn
Fixed by these parts
How to fix it
Doesn’t shut off
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JAMES from BILLINGS, MT
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken door micro switch. (unit does not start heating)
Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far l
... Read more
eft side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from ARCADIA, CA
- Parts Used:
- 6600W1K001D
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Door sensor switch went bad. Microwave would not operate.
Watched a couple of repair videos on Youtube by searching for the model number. Found out what to do in order not to get shocked by the powerful capacitor.
Ordered the two switches (To be sure, I could have ordered a third switch as suggested in the videos.)
Bought a tamper-proof star bit to get the cover off. Followed the dir ... Read more ections to replace the switches. - I broke the harness and had to use some super glue, but it's all good. I should have removed the harness instead of trying to get a switch out while it was still in place.
It's all back together, and the wife is happy!!
Ordered the two switches (To be sure, I could have ordered a third switch as suggested in the videos.)
Bought a tamper-proof star bit to get the cover off. Followed the dir ... Read more ections to replace the switches. - I broke the harness and had to use some super glue, but it's all good. I should have removed the harness instead of trying to get a switch out while it was still in place.
It's all back together, and the wife is happy!!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Chambersburg, PA
- Parts Used:
- 6912A40002E
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One of the "night" lights burned out
Unscrewed one screw that held the bulb cover over the bulb. Removed the cover, removed the bulb, inserted new bulb, replaced cover, replaced the retaining screw.
Was this instruction helpful to you?
Thank you for voting!