HMV1630DBWW Haier Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jared from SIERRA VISTA, AZ
- Parts Used:
- WB02X11550
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Had to replace charcoal filter
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimensions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimensions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CLAYTON, NJ
- Parts Used:
- WB06X10610
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Tripping circuit breaker, broken micro switch locking pin
1. Unplug unit
2. Open door, remove two screws above the top trim piece, slide and remove trim.
3. Remove screw behind control board and top left corner, then release from position.
3b. Unplug all wire terminations and set control panel aside.
4. Remove two screws securing latch board, lift and rotate board out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
2. Open door, remove two screws above the top trim piece, slide and remove trim.
3. Remove screw behind control board and top left corner, then release from position.
3b. Unplug all wire terminations and set control panel aside.
4. Remove two screws securing latch board, lift and rotate board out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from SAN ANTONIO, TX
- Parts Used:
- WB02X11550
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Charcoal Filter replaced
Open the microwave door, push the press and release door that is located across the top of the oven. Remove and replace filter, close access door, close microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from WEST CHESTER, PA
- Parts Used:
- WB10X32782
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Mirowave door latch
While installing a filter in my brand new never been used microwave range hood combo I snapped off the top door latch with my elbow. After a few expletives I search You Tube and found it was a simple fix. I ordered a replacement latch from this site. It arrived in three days and it took 5 minutes to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from RIVER EDGE, NJ
- Parts Used:
- WB02X11550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Carcoal Filter indicator light on
Loosened screw on top of filter
Removed and replaced filter
Removed and replaced filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from CHALFONT, PA
- Parts Used:
- WB02X11550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Warning light came on to replace
Ok. Surprised I was sent a damaged part. Box was intact but the aluminum frame was bent. Looks like I received a factory reject. I was able to make it fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from COLUMBIA, SC
- Parts Used:
- WB10X32782
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave door latch that was broken at bottom catch hook
I received replacement and followed youtube instructions to replace door latch mechanism. Very simple and only required a screw driver. works fine. Total time: less than 20 minutes. Wife and I are happy as I did not have to buy new a Microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from SAN TAN VLY, AZ
- Parts Used:
- WB10X32782
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door wound not shut right or lock
Used the puddy knife to open up the door and then used a screw driver to change the old part with the new one. That easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MS Bettie J from RIVERDALE PK, MD
- Parts Used:
- WB02X11550
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed filter
Open main door at the top is small door open take out old filter and replace newone
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from SUMMERFIELD, FL
- Parts Used:
- WB06X10625
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
noisy microwave turntable
I never knew why it made noise till I looked at the break down on this web site and found it was missing rotating ring since it was new. But unfortunately, I never received turntable ring which was ordered on 12/19/2022 now its tracking says Wednesday, 12/21/2022
9:36 AM
In transit
CAMP HILL, AL it has been stuck there all this time still not on its way to Florida. I don't understand did fedx put on southwest airlines?
9:36 AM
In transit
CAMP HILL, AL it has been stuck there all this time still not on its way to Florida. I don't understand did fedx put on southwest airlines?
Was this instruction helpful to you?
Thank you for voting!