Models
>
HMV1632DBWW
HMV1632DBWW Haier Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$22.91
The charcoal filter in your microwave is used to remove cooking odors from the air as they circulate through the microwave vent. The filter will last between six months to one year, depending on how o...
In Stock
Order within the next 5 hrs and your part ships today!
In Stock
Order within the next 5 hrs and your part ships today!
$149.53
This turntable tray is for microwaves.
Turntable tray rotates in the center of the microwave to help ensure the food cooks evenly.
Follow the instructions in the owner's manual when installing this part.
In Stock
Order within the next 5 hrs and your part ships today!
In Stock
Order within the next 5 hrs and your part ships today!
In Stock
Order within the next 5 hrs and your part ships today!
$51.11
The door latch housing encloses the door switches and door latch.
In Stock
Order within the next 5 hrs and your part ships today!
$114.20
This turntable motor is for microwaves.
The turntable motor rotates the glass tray inside the microwave oven.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge...
In Stock
Order within the next 5 hrs and your part ships today!
In Stock
Order within the next 5 hrs and your part ships today!
The door interlock switch lever activates the interlock switch when the door is closed.
In Stock
Order within the next 5 hrs and your part ships today!
In Stock
Order within the next 5 hrs and your part ships today!
In Stock
Order within the next 5 hrs and your part ships today!
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for HMV1632DBWW
Viewing 1 of 1
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jared from SIERRA VISTA, AZ
- Parts Used:
- WB02X11550
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Had to replace charcoal filter
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimen ... Read more sions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimen ... Read more sions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from CLAYTON, NJ
- Parts Used:
- WB06X10610
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Tripping circuit breaker, broken micro switch locking pin
1. Unplug unit
2. Open door, remove two screws above the top trim piece, slide and remove trim.
3. Remove screw behind control board and top left corner, then release from position.
3b. Unplug all wire terminations and set control panel aside.
4. Remove two screws securing latch board, lift and rotate board ... Read more out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
2. Open door, remove two screws above the top trim piece, slide and remove trim.
3. Remove screw behind control board and top left corner, then release from position.
3b. Unplug all wire terminations and set control panel aside.
4. Remove two screws securing latch board, lift and rotate board ... Read more out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from SAN ANTONIO, TX
- Parts Used:
- WB02X11550
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Charcoal Filter replaced
Open the microwave door, push the press and release door that is located across the top of the oven. Remove and replace filter, close access door, close microwave.
Was this instruction helpful to you?
Thank you for voting!