Models
>
ZEB1226SH2SS
ZEB1226SH2SS General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for ZEB1226SH2SS
Viewing 1 of 1Keep searches simple, eg. "belt" or "pump".
The roller glide in your microwave rests under the microwave plate, and allows it to rotate when the microwave is running. It is a round plastic ring with 3 wheels spaced out around the perimeter. If ...
No Longer Available
In Stock
Order within the next 3 hrs and your part ships today!
In Stock
Order within the next 3 hrs and your part ships today!
This part is the replacement wave guide cover for your microwave. It is gray in color and is approximately 3-1/2 inches long and 4 inches wide. The wave guide cover transmits microwave radiation while...
No Longer Available
On Order
In Stock
Order within the next 3 hrs and your part ships today!
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for ZEB1226SH2SS
Viewing 5 of 5Tray won’t turn
Fixed by these parts
How to fix it
No heat
Fixed by these parts
How to fix it
Door not closing properly
Fixed by these parts
How to fix it
Won’t turn on
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Merritt Island, FL
- Parts Used:
- WB27X10682
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Both Intermittent- and No-Heating
First, I read the PartsSelect DIY report by Linda, Warsaw, IN. With confidence, I purchased the magnetron. Upon receipt, I took the built-in microwave out of the cabinet, set the unit on the kitchen floor, and was stopped cold by the Safety Torx nuts on the reverse of the unit. Borrowing the right wrench allowed the 20 minute start-to-
... Read more
finish part changeout and reinstallation of the unit in the cabinet to proceed. The old magnetron was the defective part. Discovery of the 10-year Parts-Only warranty on the less than 10-year old unit was insufficinet to guide me to take the unit in for their Labor bill to repair. New part in hand, it just was that easy - and assumed to be no less expensive.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Indianapolis, IN
- Parts Used:
- WB49X10108, WB02X10895
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
brokencooking dish
easy to handle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Houston, TX
- Parts Used:
- WB34X21271
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sparks were coming out of the wave guide area whenever the microwave was turned on
1. Unplug the microwave, or cut power at the fuse box.
2. Clean the microwave in case there is any food splatters or residue.
3. Using a flathead screwdriver, pop off the plastic rivets that hold the waveguide cover in place. They should not take much to pop out.
4. Replace the damaged waveguide cover with the replacement, ... Read more reinsert plastic rivets.
5. Restore power to the microwave and test.
2. Clean the microwave in case there is any food splatters or residue.
3. Using a flathead screwdriver, pop off the plastic rivets that hold the waveguide cover in place. They should not take much to pop out.
4. Replace the damaged waveguide cover with the replacement, ... Read more reinsert plastic rivets.
5. Restore power to the microwave and test.
Read less
Was this instruction helpful to you?
Thank you for voting!