PEB9159SJ2SS General Electric Microwave - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Henry from NORWALK, CT
- Parts Used:
- WB10X27080, WB14X10049
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave door was hard to open
1. Take out the case by unscrew 8 screws on the back and side of the case
2. Take out the control panel by unscrew 1 screw on the top and slide up
3. Take out the latch by unscrew 2 screws, and slide out 3 electric switches that clipped on the latch
4. Clip the switches onto the new latch
5. Slide in lever switch into latch
6. Put back the latch
7. Put back the control panel
8. Put back the case
2. Take out the control panel by unscrew 1 screw on the top and slide up
3. Take out the latch by unscrew 2 screws, and slide out 3 electric switches that clipped on the latch
4. Clip the switches onto the new latch
5. Slide in lever switch into latch
6. Put back the latch
7. Put back the control panel
8. Put back the case
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from WESLEY CHAPEL, FL
- Parts Used:
- WB14X10049
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Door locks. Not opening.
Slide a Butter knife at left side by open push knob door will open. Then open all screws from top cover push cover top side front way then door locks Bracket have 3 microswitch pulls out switches mark them top medium and bottom. Remove 3 screws holding brackets will come out. On bottom see a Cam has 1/4” holes can holding Saft broken then install new door lock bracket install microswitch put 3screw and slide Cam on saft . I put a small screw on saft to hold cam on place. There was no screw . That’s why cam saft was broke. Put top cover tight all the screws and door lock fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hillsdale, NJ
- Parts Used:
- WB27X29822
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Control board partially working
You will need a security or tamper proof torx
Screwdriver to remove the outer cover. Take pictures before removing the connectors to the control board. 2 Phillips hard screws to remove the board and snap board out of side clips. There are also eight connector wires to detach. Used needle nose pliers.
Overall, not a difficult repair.
Screwdriver to remove the outer cover. Take pictures before removing the connectors to the control board. 2 Phillips hard screws to remove the board and snap board out of side clips. There are also eight connector wires to detach. Used needle nose pliers.
Overall, not a difficult repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darilyn from Woburn, MA
- Parts Used:
- WB39X10032
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Microwave glass turntable was washed, placed in strainer. The weight of the turntable forced the sink strainer to tumble to the kitchen floor shattering the turntable.
Ordered the part with brand name and model number on Monday.
Ordered part was delivered to an incorrect address the following Wednesday.
A street resident delivered the ordered part to me on the following Sunday.
Ordered part was delivered to an incorrect address the following Wednesday.
A street resident delivered the ordered part to me on the following Sunday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from KIRKLAND, WA
- Parts Used:
- WB39X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Installed waveguide
Inserted the waveguide into the slots on the side of microwave.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Greenville, MI
- Parts Used:
- WB39X10034, WB01X10418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wave guide cover loose, caused short
Took off old cover, stuck new one in. Pushed two plastic nails into holes.
Was this instruction helpful to you?
Thank you for voting!