Models > JES1456DS3WW

JES1456DS3WW General Electric Microwave

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for JES1456DS3WW

Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$16.32
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
In Stock
This interlock switch is located in the door latch.
In Stock
This tray rotates in your microwave ensuring more even temperatures.
In Stock
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside yo...
In Stock
$28.99
This roller guide sits underneath the glass turntable tray.
In Stock
$23.37
In Stock
This part is the replacement light bulb for your microwave. This bulb is 125 volts and 25 watts. It should come on automatically when you open your microwave door, or if the microwave is running. If y...
In Stock
This motor rotates the glass turntable in the microwave.
In Stock
Genuine OEM magnetron for your microwave. Always use proper safety equipment and follow the manufacturers instructions while installing.
In Stock
$17.56
In Stock
In Stock
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for JES1456DS3WW

Viewing 7 of 7
No heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Won’t turn on
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Tray won’t turn
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Touchpad does not respond
Fixed by these parts
Fixing
How to fix it
Doesn’t shut off
Fixed by these parts
Fixing
How to fix it
Door not closing properly
Fixed by these parts
Fixing
How to fix it
Noisy
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
  • Customer:
    Kim from Cliffside Park, NJ
  • Parts Used:
    WB27X10928
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
951 of 1225 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Ralph from Brandon, FL
  • Parts Used:
    WB27X10928
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
I diagnosed the problem incorrectly: based on a previous repair.
The old fuse is perfectly good. The new ones arrived within a day.
64 of 135 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • Customer:
    Thomas from Andover, NJ
  • Parts Used:
    WB24X10047
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Microwave runs with the door open
Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover
and test to see if that solved the problem. If so then well done!!
35 of 50 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!