Models > CEB1599SJ1SS > Instructions

CEB1599SJ1SS General Electric Microwave - Instructions

Jump to:

All Instructions for the CEB1599SJ1SS

Customer:: Henry from NORWALK, CT
Parts Used:: WB10X27080, WB14X10049
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Microwave door was hard to open

1. Take out the case by unscrew 8 screws on the back and side of the case
2. Take out the control panel by unscrew 1 screw on the top and slide up
3. Take out the latch by unscrew 2 screws, and slide out 3 electric switches that clipped on the latch
4. Clip the switches onto the new latch
5. Slide in lever switch into latch
6. Put back the latch
7. Put back the control panel
8. Put back the case

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jay from WESLEY CHAPEL, FL
Parts Used:: WB14X10049
Difficulty Level:: Really Easy
Total Repair Time:: 1- 2 hours
Tools:: Screw drivers

Door locks. Not opening.

Slide a Butter knife at left side by open push knob door will open. Then open all screws from top cover push cover top side front way then door locks Bracket have 3 microswitch pulls out switches mark them top medium and bottom. Remove 3 screws holding brackets will come out. On bottom see a Cam has 1/4” holes can holding Saft broken then install new door lock bracket install microswitch put 3screw and slide Cam on saft . I put a small screw on saft to hold cam on place. There was no screw . That’s why cam saft was broke. Put top cover tight all the screws and door lock fixed.

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Moin from SCOTTSDALE, AZ
Parts Used:: WB24X10190
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Pliers, Screw drivers

WHEN. YOU OPEN THE DOOR THE TURN TABLE WAS CONSTANTLY RUNNING

REPLACE SWITCH -STAND ON (NOT THE SWITCH-MONITOR) THERE ARE TWO OF THESE SWITCHES THE TOP ONE WAS DEFECTIVE.
THE ON OFF SWITCH BUTTON ON THE SWITCH WAS BROKEN

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Jason from KIRKLAND, WA
Parts Used:: WB39X10034
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Installed waveguide

Inserted the waveguide into the slots on the side of microwave.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: James from Decatur, MS
Parts Used:: WB56X27090
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

75% of the buttons stopped working

1. Remove/unplug microwave
2. Remove microwave cover using torx security bits and sliding backwards then lifting off.
3. Unplug and note location of all electrical connections on control board (taking a picture is a good idea)
4. Remove the one Phillips head screw at the top of the control panel.
5. Lift up and remove control panel.
6. Replace with new control panel by positioning slightly higher to engage bottom tabs and pressing down.
7. Replace Phillips head screw at the top of the control panel.
8. Reconnect all electrical connections.
9. I like to plug it in and test for functionality here. CAREFUL OF OPEN ELECTRICAL COMPONENTS!
10. Replace cover by placing slightly behind front cover and sliding forward then replace all screws. NOTE: make sure all edges are secured.
11. Plug in and replace microwave.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Larry from Greenville, MI
Parts Used:: WB39X10034, WB01X10418
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Wave guide cover loose, caused short

Took off old cover, stuck new one in. Pushed two plastic nails into holes.

Was this instruction helpful to you?

All Instructions for the CEB1599SJ1SS