Models
>
JEB1095BB002
JEB1095BB002 General Electric Microwave
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JEB1095BB002
Viewing 2 of 2Manuals & Guides for JEB1095BB002
Click to downloadInstall
Installation Instructions
(0.25MB)
Install
Installation Instructions
(0.27MB)
Manual
Owner's Manuals
(2.72MB)
Specs
Product Specifications Sheet
(0.15MB)
Care
Use and Care Manual
(1.03MB)
Keep searches simple, eg. "belt" or "pump".
$22.00
This 40-Watt 130-Volt lightbulb is a genuine OEM replacement for your microwave. The bulb is used either inside the microwave and turns on when the door is open, or the appliance is running. Or it can...
In Stock
In Stock
In Stock
$112.83
The capacitor is an electric circuit element that is used to store charge temporarily.
In Stock
In Stock
Special Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JEB1095BB002
Viewing 2 of 2Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- william from san antonio, TX
- Parts Used:
- WB36X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
bulb had broken off in base that was still screwed into socket
At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you c
... Read more
an drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Theodore from Medical Lake, WA
- Parts Used:
- WB27X10597
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not working as far as heating or cooking
Replaced High Voltage Diode. Very carfully due to the extream danger of a electrical shock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Gilbert, AZ
- Parts Used:
- WB27X10089
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
microwave would not heat up
I removed the microwave unit (built-in) from the housing above the built-in oven with just two screws and unplugging it. I then removed the screws from the top and sides of the microwave access panels to allow access to the magnetron. I then removed the electrical connections from the magnetron, which is very simple and then the screws w
... Read more
hich held the magnetron in place. Replacement of the new part was just the reverse of removing the other one. Cost to do this by a technician would have been somewhere in the neighborhood of $65.00 for coming to the house, and $75.00 per hour rounded to probably 2 hours to do it. So, doing this yourself is satisfying not only in knowing you did the job, but the $200.00 plus dollars you saved as well.
Read less
Was this instruction helpful to you?
Thank you for voting!